Sanuvox COILCLEAN IL - Manual (Page 6)

UV SYSTEM ‘ON’ / SISTEMA UV 'ENCENDIDA'
UV LAMP TO BE REPLACED / LÁMPARA UV QUE SER REEMPLAZADO
UV LAMP FAILURE / FALLOS DE LA LÁMPARA UV
NO POWER (LED OFF) / NO HAY ENERGIA (LED APAGADO)
STATUS UV LAMP 2 UV LAMP 1
UNDERSTANDING BALLAST LED DISPLAY & DRY CONTACTS
UV SYSTEM ‘ON’ : The system is functioning normally
UV LAMP TO BE REPLACED : Notifies the user that the Lamp
has reached the end of its serviceable life (24 months of real-
time operation) and must be replaced
UV LAMP FAILURE :
powered ON with no UV Lamp installed
Flashes if Lamp has failed or the unit is
NO POWER (LED OFF) : There is no power being delivered to the
system or defective power supply
The CoilClean incorporates unique features into the ballast control box. These include LED status
display as well two pairs of Dry Contacts designed to communicate with building automation systems.
LED Status Display
The CoilClean IL Ballast box may have one or two ballasts incorporated into the box depending on
how many units were ordered. If only one ballast is incorporated into the ballast box, you will notice
only one wire set incorporated into the box and a black button covering where a second LED would
be. If the ballast box incorporates two ballasts there will be two LEDs that corresponding to each UV
Lamp.
A reset button is located under the LED (when cover is removed) allowing the user to “Reset” the
display back to factory condition. To be performed after UV Lamp replacement.
Dry-Contacts for Building Automation Integration
Each UV CoilClean IL system includes a pair of Dry Contacts (NO & NC). Dry Contacts make it
possible for the CoilClean ILs to be easily tied to building automation systems.
(Green)
(Yellow)
(Red)
(LED OFF)
LED w/
Reset
NO: normally open
Neutral
NC: normally closed
CoilClean IL Part Numbers (Includes Lamp, Assembly, Hardware & Ballast)
IL12-G: Inside Air Handler Lamp Length 12” long 120 volt (IL12/220-G:230 Volt)
IL18-G: Inside Air Handler Lamp Length 18” long 120 volt (IL18/220-G:230 Volt)
IL24-G: Inside Air Handler Lamp Length 24” long 120 volt (IL24/220-G:230 Volt)
IL30-G: Inside Air Handler Lamp Length 30” long 120 volt (IL30/220-G:230 Volt)
IL40-G: Inside Air Handler Lamp Length 40” long 120 volt (IL40/220-G:230 Volt)
IL50-G: Inside Air Handler Lamp Length 50” long 120 volt (IL50/220-G:230 Volt)
IL60-G: Inside Air Handler Lamp Length 60” long 120 volt (IL60/220-G:230 Volt)
CoilClean IL Replacement UV Lamps
LMPHGS120: T6 High-Intensity Germicidal (UVC) 12” Straight UV Lamp for IL12
LMPHGS180: T6 High-Intensity Germicidal (UVC) 18” Straight UV Lamp for IL18
LMPHGS240: T6 High-Intensity Germicidal (UVC) 24” Straight UV Lamp for IL24
LMPHGS300: T6 High-Intensity Germicidal (UVC) 30” Straight UV Lamp for IL30
LMPHGS400: T6 High-Intensity Germicidal (UVC) 40” Straight UV Lamp for IL40
LMPHGS500: T6 High-Intensity Germicidal (UVC) 50” Straight UV Lamp for IL50
LMPHGS600: T6 High-Intensity Germicidal (UVC) 60” Straight UV Lamp for IL60
CoilClean Replacement Ballasts
BST120W5: 120 Volt Electronic Ballast for IL12, IL18, IL24, IL30
(Available 220 Volt & 277 Volt)
BST120W7: 120 Volt Electronic Ballast for IL40, IL50, IL60
(Available 220 Volt & 277 Volt)
Flange Mounting Bracket
FLANGE part# MSC9
CONNECTOR part# MSCCON19
PART NUMBERS
Disconnect all power before performing any maintenance
or service. UV Lamps need periodic replacement to
maintain design specifications. Replace UV Lamps after
17,000 hours of operation. Use caution when removing
and inserting UV Lamps from the metal spring clamps.
Use only specified Sanuvox UV Lamps with this UV
system. Other UV Lamps may plug into the accessory, but
they should not be used. The use of an incorrect lamp can
result in damage to system or UV Lamp.
MAINTENANCE
DRY CONTACTS
6
WARRANTY
Lamp Change-Out: 17,000 hours (2 years)
Lamp Warranty: 2 years
Electronics: 1 year
Ballast Warranty: 15 years