HITEC ParkMaster 3D - Manual (Page 9)

9
# 21 4231
Examine your kit carefully!
MULTIPLEX model kits are subject to constant quality checks throughout the production process, and we sincerely hope that you are
completely satisfied with the contents of your kit. However, we do ask you to check all the parts before you start construction
(referring to the Parts List), as we cannot exchange components which you have already worked on. If you find any part is not
acceptable, we will readily correct or exchange it once we have examined it. Just send the component to our Model Department.
Please be sure to include the purchase receipt and the completed complaint form, which is included in the kit.
We are constantly working on improving our models, and for this reason we must reserve the right to change the kit contents in
terms of shape or dimensions of parts, technology, materials and fittings, without prior notification. Please understand that we
cannot entertain claims against us if the kit contents do not agree in every respect with the instructions and the illustrations.
Caution!
Radio-controlled models, and especially model aircraft, are by no means playthings. Building and operating them safely
requires a certain level of technical competence and manual skill, together with discipline and a responsible attitude at the
flying field. Errors and carelessness in building and flying the model can result in serious personal injury and damage to
property. Since we, as manufacturers, have no control over the construction, maintenance and operation of our products, we
are obliged to take this opportunity to point out these hazards and to emphasise your personal responsibility. Even though the
model is called the “ParkMaster 3D”, you can only fly in the park if model flying is expressly permitted there.
Additional items required for the “ParkMaster 3D”:
MULTIPLEX radio control components for the ParkMaster 3D:
MULTIPLEX RX-6-SYNTH light receiver
35 MHz A+B band Order No. 5 5876
alternatively: 40 / 41 MHz band Order No. 5 5877
Nano-Karbonite servo (four required) 2 x aileron, 1 x
elevator, 1 x rudder
Order No. 6 5118
Possibly 200 mm UNI suppressor filter lead (for speed controller) Order No. 8 5035
Battery charger:
MULTIcharger LN-3008 EQU
Order No. 9 2540
For 2S and 3S LiPo, LiIo and LiFe batteries, and
4-cell to 8-cell NiMH and NiCd batteries
ParkMaster 3D power set
Contents:
Order No. 33 2638
Himax 2816-0890 motor, BL-17 II speed controller, APC 11 x 5.5” propeller, taper collet and propeller driver.
Flight battery Li-BATT BX-3/1 950 Order No. 15 7116
Tools:
Scissors, balsa knife, combination pliers, side-cutters.
Note: please remove the illustration pages from the centre of the instructions.
Specification:
Wingspan:
960 mm
Overall length: 1000 mm
All-up weight approx.: 525 g
Total surface area: 29 dm²
Wing loading min.: 18 g/dm²
RC functions: Aileron, elevator, rudder, throttle
Important note
This model is not made of styrofoam™, and it is not possible to glue the material using white glue, polyurethane or epoxy;
these adhesives only produce a superficial bond which simply gives way when stressed. Please use medium-viscosity
cyano-acrylate glue exclusively, preferably our Zacki-ELAPOR®, # 59 2727 - the cyano glue optimised specifically for
ELAPOR® particle foam.
If you use Zacki-ELAPOR® you will find that you do not need cyano kicker or activator for most joints. However, if you
wish to use a different adhesive, and are therefore obliged to use kicker / activator spray, we recommend that you apply
the material in the open air to avoid health problems.