HITEC FunJet Ultra - Manual (Page 12)

12
angle of 20 - 30°.
Don’t launch the model “downhill”, like a glider!
Allow the aeroplane to climb to a safe altitude, then adjust the
trims on the transmitter so that the model flies straight and
level without any assistance from you.
While the FunJet ULTRA is still at a safe altitude, switch off the
motor and try out the controls on the glide.
23. Safety
Safety is the First Commandment when flying any model
aircraft. Third party insurance should be considered a basic
essential. If you join a model club suitable cover will usually be
available through the organisation. It is your personal
responsibility to ensure that your insurance is adequate (i.e.
that its cover includes powered model aircraft).
Make it your job to keep your models and your radio control
system in perfect order at all times. Check the correct charging
procedure for the batteries you are using. Make use of all
sensible safety systems and precautions which are advised
for your system. An excellent source of practical accessories
is the MULTIPLEX main catalogue, as our products are
designed and manufactured exclusively by practising
modellers for other practising modellers.
Always fly with a responsible attitude. You may think that flying
low over other people’s heads is proof of your piloting skill;
others know better: the real expert does not need to prove
himself in such childish ways. Let other pilots know that this is
what you think too. Always fly in such a way that you do not
endanger yourself or others. Bear in mind that even the best
RC system in the world is subject to outside interference. No
matter how many years of accident-free flying you have under
your belt, you have no idea what will happen in the next minute.
All of us in the MULTIPLEX team hope you have many hours
of pleasure building and flying your new model.
MULTIPLEX Modellsport
Product development and maintenance
Klaus Michler
Parts list - FunJet ULTRA
Part No. Description Material Dimensions
No. off
1 1 KIT building instructions
2A 1 Decal set (sheet A) Printed adhesive film 350 x 500 mm
2B 1 Decal set (sheet B) Printed adhesive film 350 x 500 mm
3 1 Fuselage Moulded Elapor foam Ready made, silver
4 1 Fuselage turtle deck Moulded Elapor foam Ready made, silver
5 1 Canopy Moulded Elapor foam Ready made, silver
6 1 L.H. wing panel Moulded Elapor foam Ready made, silver
7 1 R.H. wing panel Moulded Elapor foam Ready made, silver
8 1 L.H. fin Moulded Elapor foam Ready made, silver
9 1 R.H. fin Moulded Elapor foam Ready made, silver
10 1 Tubular spar CFRP tube 6 Ø x 4 Ø x 575 mm
11 1 FunJet motor mount Inj. moulded plastic Ready made
Small items set
20
3 Hook-and-loop tape, hook Plastic 25 x 60 mm
21 3 Hook-and-loop tape, loop Plastic 25 x 60 mm
22 2 Canopy latch Inj. moulded plastic Ready made
23 2 Canopy latch tongue Inj. moulded plastic Ready made
24 2 Glue-fitting horn Inj. moulded plastic Ready made
25 2 Swivel pushrod connector Metal Ready made, 6 mm Ø
26 2 Washer Metal M2
27 2 Nut Metal M2
28 2 Socket-head grubscrew Metal M3 x 3 mm
29 1 Allen key Metal 1.5 mm A/F
30 2 Pre-formed elevon pushrod Metal 1 Ø x 80 mm
31 1 L.H. servo fairing Vac. moulded plastic Ready made
32 1 R.H. servo fairing Vac. moulded plastic Ready made
33 1 Motor bulkhead Inj. moulded plastic Ready made
34 2 Motor bulkhead screw Metal M3 x 16 mm
36 1 Motor bulkhead adjuster screw. Metal M3 x 22 mm
37 1 Battery support plate Plastic 20 x 60 mm
38 1 Battery retaining strap Plastic 16 x 200 mm
39 1 Cable retainer Plastic Ready made