Hanna Instruments HI 93530 - Manual (Page 10)

19 18
ACCESSORIES
K-TYPE THERMOCOUPLE PROBES
with integral handle, 1 m (3.3') cable & mini-connector
HI 766A Roller surface probe, max 320°C/600°F
HI 766B Surface probe, max 650°C/1200°F
HI 766B1 90º surface probe, max 450°C/840°F
HI 766B2 Spring-loaded, surface probe, max 900°C/1650°F
HI 766B3 Spring-loaded, small surface probe w/insulated shaft
HI 766C Penetration probe, max 900°C/1650°F
HI 766C1 Ultra-fast Penetration probe, max 300°C/570°F
HI 766D Air probe, max 300°C/570°F
HI 766E1 General purpose probe, max 900°C/1650°F
HI 766F High temperature, flexible wire probe without handle
HI 766F1 Flexible wire probe w/o handle, max 480°C/900°F
HI 766TR1 Penetration probe, max 250°C/482°F
HI 766TR2 Penetration long probe, max 250°C/482°F
HI 766TV1 Pipe clamp probe, max 200°C/390°F
with detachable handle & mini-connector (to be used in con-
junction with the HI 766HD probe handle)
HI 766PA Roller surface probe, max 320°C/600°F
HI 766PB Surface probe, max 650°C/1200°F
HI 766PC Penetration probe, max 900°C/1650°F
HI 766PD Air probe, max 300°C/570°F
HI 766PE1 General purpose probe, max 900°C/1650°F
grill surface probe
HI 766B4 Grill surface probe with 70 cm (27.6’’) cable (protected
with stainless steel jacket), max 250°C/482°F
HI 7664B4S Spare stainless steel sensor for HI 766B4 probe
OTHER ACCESSORIES
HI 710007 / 8 Shockproof rubber boot, blue / orange
HI 710018 Spare protective case
HI 766EX Extension cable for K-type probes
HI 92000 Windows ® compatible software
HI 920011 Serial cable for PC connection
Recommendations for Users
Before using these products, make sure that they are entirely suitable for the
environment in which they are used. Operation of these instruments in residential
area could cause unacceptable interferences to radio and TV equipments, requiring
the operator to take all necessary steps to correct interferences. Any variation intro-
duced by the user to the supplied equipment may degrade the instruments' EMC
performance. To avoid electrical shock, do not use these instruments when voltages
at the measurement surface exceed 24 Vac or 60 Vdc. To avoid damages or burns,
do not perform any measurement in microwave ovens.
USER CALIBRATION
(Not for HI 93530, HI 93531 and HI 93532 models)
The meters can be calibrated at 0°C by using an ice bath.
• Prepare an ice bath with approximately equal volumes of distilled
water and chopped ice made from distilled water.
• Immerse the temperature probe in the center of the ice bath,
taking care not to touch the ice with the probe tip.
• Ensure that the meter is measuring a temperature within ±3°C.
• To enter the Calibration mode, press and hold the CAL button for
about 5 seconds.
• The CAL tag turns on to indicate that the
Calibration mode has been entered.
Note: If the measurement is outside the
±3°C window, the meter does not
enter Calibration mode.
• When the meter reaches the stability condition, which is detected
when the measurement remains within ±0.2°C for 5 seconds,
the calibration is accepted and the reading becomes 0°C (32°F).
• The meter then automatically returns to normal mode.
Note: To exit the Calibration mode at any time, press the CAL key.
Note: User calibration cannot be entered in T1-T2 mode.
Note: User calibration is only performed on the current channel
displayed (T1 or T2).
FACTORY RECALIBRATION
All Hanna thermometers have been accurately pre-calibrated at the
factory.
It is generally recommended to have all thermometers recalibrated at
least once a year.
For an accurate recalibration, contact your nearest Hanna Customer
Service Center.
Note: To clean the meters, do not use aggressive detergents. It is
recommended to use water.