Grandview 1GD-868MnIII(RF Remote Controller) - Manual (Page 4)

Model：1GD-868Mn
Installation of the Receiver
Wiring Instruction
The below diagram showcase the wire connection, please following the below instruction during
installation
> The power must be cut before wiring
> Please prevent from static electricity as it may damage to some electronic parts
> Please use cables that match the local safety standard
> The earth wire must be connected
> When connecting the control box externally, please make sure the loop resistance is less than 20Ω.
If the cable lies nearby the strong current, please try to use shielded wire. The qualified UTP cable is
recommend for total cable length within 100 meter as the resistance is around 9.2Ω.
UP
DOWN
STOP
MICRO-UP MICRO-DOWN
The Remote control is compatible with the receiver, transfer signal by
Radio Wave(868MHz).
Model:1GD-868Mn
1. Press ▲ to lift the screen.
2. Press ○ to stop the screen
3. Press ▼ to lower the screen.
4. The Micro switch is used for retracting or lowering screen in small
increments.
Operating Instruction for Using Remote:
FUNCTION ：
Please read the below instruction before installing the receiver
Attention:
> When installing the receiver, please make sure the cable
exit face down to prevent from potential infiltrationwater
> Please keep away from large size metal objects when installing the receiver in case the frequency
is affected
> Please make sure the distance between two receiver
should be at least 20 cm
Dimension
metal
1. Working Temperature:-5℃~+40℃;
2. Protection Rate:IP40;
3. In order to avoid leakage,please take out of the battery when storing it
for a long time without use.
Cautions for Remote:
1. Press the programming button of the receiver(SW5), the Led(FD1)will twinkle in gree and indicating it is in
programming mode.
2. Then loose the button, press up/stop switch of the remote controller until the Led(FD1) light on, then loose the
button,means the programming is sucessful.
Programming Setting and Clear for Remote Control
Programming Code Setting(Step by Step)
Programming Code Cleaning(Step by step)
1. Press the Programming button of the receiver(SW5) in 5 seconds, the Led(FD1)will twinkle from slowly to quickly.
2. Then loose the button, press it again, the Led(FD1)will light on, which means the programming code is clear.
Note:
1. Please make sure setting the programming code in 15 second when the LED (FD1) twinkle in green,otherwise it will
be failed.
2. Pls do not start programming setting when the screen is rolling.
3. When in the process of programming code setting,the remote will stop working.
Instruction for Manual Switch of Receiver (Pls refer to Drawing of Page3)
When the remote control don’t work,you can handle the screen by Manual Switch instead.
Mannual control of Direction Exchange Switch for Motor(SW1) Manual Instruction:
When controlling the screen by mannual control, If you found the screen rolling in a contrary direction and confrim
operate the remote in a right way (that means when you press the up button the screen goes downwards,when you
press the down button,the screen goes upwards). Please just turn turn the (SW1) switch which is inside of the
Receiver , the screen will properly working again.
If you found the screen rolling in a contrary direction(when you press the up button the screen goes downwards, when
you press the down button,the screen goes upwards),you only needs to open the receiver and change the cables for
R1 and L1.
RS485/RS232 Configuration
Central Control Protocol
1. Communication Protocol:
2. UP: 0xFF 0xEE 0xEE 0xEE 0XDD
3. STOP: 0xFF 0xEE 0xEE 0xEE 0XCC
4. DOWN: 0xFF 0xEE 0xEE 0xEE 0XEE
5. MICRO-UP: 0xFF 0xEE 0xEE 0xEE 0xC9
6. MICRO-DOWN: 0xFF 0xEE 0xEE 0xEE 0xE9
7. Initial Code: 0xFF 0xXX 0xXX 0xXX 0xAA
DATA BITS: 8 Digits INTIAL DIGITS: Digit 1 STOP DIGITS: Digit 1 BAUD RATE: 2400
Sw1
S w
4
S
w 3
S w
2
SW5 SW5
Indicating Light
Power Light
Learning button
Manual Button
Up/Down
Down/up
Stop
Power Source
Wiring
1
3
2
6
7
5
4
L
N
N
Live Wire Brown
Null Wire
E Earth Wire Yellow Green
E Earth Wire
Null Wire
R Up/Down Wire
L Up/Down Wire
Model No. 230V Color Name ID
Motor
Line
Power
Line
Direction Exchange
Switch
Motor
115V Color
External
Switch
8
9
10
11
Up Wire
Down Wire
Stop Wire
Concentric Wire
Black
Green
Blue
Blue Blue
White
Yellow Green Yellow Green
Brown Brown
Black Black
Attention: Please make sure the wiring is strictly following the diagram and the
diagram is only base on our product.
Up
Stop
Down
Con
12
13 5
3 RS232-TXD
RS232-GND
12 13