Assemble components to the pc board – Elenco Christmas Tree Kit User Manual
Page 5

-4-
ASSEMBLE COMPONENTS TO THE PC BOARD
Figure C
Insert the IC socket into
the PC board with the
notch in the direction
shown on the top legend.
Solder the IC socket into
place. Insert the IC into
the socket with the notch
in the same direction as
the notch on the socket.
Notch
IC
Socket
PC Board
D9 - Red LED
(see Figure A)
R17 - 1.2k
Ω 5% 1/4W Resistor
(brown-red-red-gold)
D3 - Yellow LED
(see Figure A)
R7 - 1.2k
Ω 5% 1/4W Resistor
(brown-red-red-gold)
D2 - Red LED
(see Figure A)
R4 - 1.2k
Ω 5% 1/4W Resistor
(brown-red-red-gold)
D4 - Yellow LED
(see Figure A)
R8 - 1.2k
Ω 5% 1/4W Resistor
(brown-red-red-gold)
C3 - 10
μF Electrolytic Cap.
(see Figure B)
R6 - 56k
Ω 5% 1/4W Resistor
(green-blue-orange-gold)
C2 - .01
μF (103) Capacitor
R1 - 10k
Ω 5% 1/4W Resistor
R5 - 10k
Ω 5% 1/4W Resistor
(brown-black-orange-gold)
R2 - 68k
Ω 5% 1/4W Resistor
(blue-gray-orange-gold)
14-pin IC Socket
U1 - 556 Integrated Circuit
(see Figure C)
J3 - Jumper Wire
(see Figure D)
C1 - 10
μF Electrolytic Cap.
(see Figure B)
C4 - .01
μF (103) Capacitor
S1 - Slide Switch
(Cut off excess leads)
R15 - 1.2k
Ω 5% 1/4W Resistor
(brown-red-red-gold)
D7 - Green LED
D1 - Red LED
(see Figure A)
R16 - 1.2k
Ω 5% 1/4W Resistor
R3 - 1.2k
Ω 5% 1/4W Resistor
(brown-red-red-gold)
D8 - Green LED
D5 - Yellow LED
(see Figure A)
R11 - 1.2k
Ω 5% 1/4W Resistor
(brown-red-red-gold)
D6 - Green LED
(see Figure A)
R12 - 1.2k
Ω 5% 1/4W Resistor
(brown-red-red-gold)
C8 - .01
μF (103) Discap
R14 - 33k
Ω 5% 1/4W Resistor
(orange-orange-orange-gold)
J2 - Jumper Wire
(see Figure D)
R10 - 47k
Ω 5% 1/4W Resistor
(yellow-violet-orange-gold)
14-pin IC Socket
U2 - 556 Integrated Circuit
(see Figure C)
C5 - 10
μF Electrolytic Cap.
(see Figure B)
C6 - .01
μF (103) Discap
J1 - Jumper Wire
(see Figure D)
R9 - 10k
Ω 5% 1/4W Resistor
R13 - 10k
Ω 5% 1/4W Resistor
(brown-black-orange-gold)
C7 - 10
μF Electrolytic Cap.
(see Figure B)
Figure A
Mount the LED flush to
the PC board with the flat
side in the same direction
as marked.
Flat
Figure B
Electrolytic capacitors have
polarity. Mount the capacitor
with the positive lead in the hole
marked (+) on the PC board.
Warning: If the capacitor is
connected with incorrect polarity
it may heat up and either leak or
cause the capacitor to explode.
Polarity
Marking
(–)
(+)
Figure D
Form a discarded piece of
an electrolytic lead into a
jumper wire by bending
the wire to the correct
length and mount it to the
PC board.
PC Board Marking