Datacom Systems 1000BT-AT-SX - Manual

Warranty
Datacom Systems, Inc. (DSI) warrants that the hardware which it supplies will be free
from significant defects in materials and workmanship for a period of two years from
the date of delivery (Warranty Period), under normal use and conditions. In the event
of any such defect, you can return an item of defective hardware, freight prepaid, to
DSI during the W arranty Period, and DSI will repair or replace the defective equipment
and return it to you, freight prepaid. If DSI determines that the equipment is not defec-
tive, it will return it to you, freight collect. DSI shall have no responsibility for any
deficiency resulting from accidents, misuse, modifications, power disturbances
(including use of a power supply not specified by DSI), or various other forms of dis-
aster, e.g., earthquakes, floods, etc.
PLEASE DO NOT A TTEMPT TO RETURN ANY ITEM PRIOR TO RECEIVING
ARETURN MA TERIALAUTHORIZA TION (RMA) NUMBER FROM DATACOM
CUSTOMER SER VICE A T (315) 463-9541
Limitation On Liability
The warranties set forth above are exclusive and in lieu of all other warranties.
Datacom Systems, Inc. (DSI) makes no other warranties, expressed or implied, and
DSI expressly disclaims all other warranties, including but not limited to implied war-
ranties of merchantability and fitness for a particular purpose. Moreover, the provisions
set forth above state DSI’s entire responsibility and your sole and exclusive remedy
with respect to any breach of warranty or contract.
No liability for consequential damages. Under no circumstances and under no theory
of Liability shall DSI be liable for costs of procurement of substitute products or serv-
ices, lost profits, lost savings, loss of information or data, or any other special, indirect,
consequential or incidental damages, arising in any way out of the sale of, use of, or
inability to use, any DSI product or service, even if DSI has been advised of the possi-
bility of such damages.
DATACOMsystems ®
1000BT-AT-SX Full-Duplex Tap
Quick Installation Guide
Copyright
Copyright © 2003 by Datacom Systems, Inc. All rights reserved. Printed in the
United States of America. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted, in any form or by any means, elec-
tronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Datacom Systems, Inc. To obtain this permission, write
to the attention of the Datacom Systems legal department at
9 Adler Drive, East Syracuse, New York 13057-1290, or call 315-463-9541.
Customer Service
This Quick Installation Guide was written to help you get to know your new
10/100-AT quickly and easily. We would welcome any comments or sugges-
tions you may have regarding this Quick Installation Guide. Please send your
remarks and recommendations via mail, telephone, facsimile, or Internet E-
mail.
Datacom Customer Service personnel are available from 8 AM to 5:30 PM
Eastern time, weekdays. Customer Service is available via telephone, facsimile,
and Internet E-mail. Outside of support hours, please leave a voice message and
our Customer Service Staff will return your call as soon as possible.
Mail: Datacom Systems, Inc.
Customer Service
9 Adler Drive
East Syracuse, NY 13057-1290
Tel: (315) 463-9541
FAX: (315) 463-9557
E-mail: [email protected]
World Wide Web
You can obtain additional information about Datacom Systems, Inc. and its
products and services from the World Wide Web at http://www.datacomsys-
tems.com.
February 2004
Part Number: 541-0078-A.00
Empowering Network Professionals ™
DATACOM
SYSTEMS INC ™
DATACOMsystems ® Family of Products
11/10/2003
OPTICALswitch ™
MODEL PORTS TOPOLOGY CONNECTIVITY
1X8SP-OM ( S) 8 100FX, OC3, OC12, Gigabit Dual SC
1X8SY-OM (S) 8 100FX, OC3, OC12, Gigabit Dual SC
LANswitch ™
ATM In-Line
MODEL PORTS TOPOLOGY CONNECTIVITY
2X8SY-ATM-M (S) 2x8 ATM, OC3-OC12 Dual SC
Ethernet/Token Ring
MODEL PORTS TOPOLOGY CONNECTIVITY
2X16FD-SY 2x16 10/100 BaseT RJ45
MX8100E/Tsl 2x8 10/100 BaseT or Token RJ45
MX16100E/Tsl 2x16 10/100 BaseT or Token RJ45
Fiber Custom
MODEL PORTS TOPOLOGY CONNECTIVITY
4XSPSY-CM 4 Gigabit Dual SC
4X8SY-SX 4X8 Gigabit Dual SC
4X8SP4-SX 4X8 Gigabit Dual SC
4X16SP-SX 4X16 Gigabit Dual SC
Gigabit In-Line
MODEL PORTS TOPOLOGY CONNECTIVITY
1X8SY-SX (LX) 1x8 Gigabit Dual SC
2X8SY-SX (LX) 2x8 Gigabit Dual SC
Gigabit SPAN
MODEL PORTS TOPOLOGY CONNECTIVITY
1X8SP-SX (LX) 1x8 Gigabit Dual SC
2X4SY-SX (LX) 2x4 Gigabit Dual SC
2X8SY-SX (LX) 2x8 Gigabit Dual SC
Gigabit SPAN + In-Line
MODEL PORTS TOPOLOGY CONNECTIVITY
2X8SP4-SX (LX) 2x8 Gigabit Dual SC
Receive Only
MODEL PORTS TOPOLOGY CONNECTIVITY
2X8RX-SX 2x8 Gigabit Dual SC
ACCESSORY
Software
MANAgents — Multiple Agent Controlling Console Software
Support
M3415A — V.35 Connectivity Panel
RMC-3 — 1U Rack Panel for 3 Small Form DSI Products
SCS — Switch Control Server
TAP
Ethernet/Token Ring
MODEL PORTS TOPOLOGY CONNECTIVITY
10/100-AT 1 10/100 BaseT RJ45
1000BT-AT 1 1000 BaseT RJ45
Fiber
MODEL PORTS TOPOLOGY CONNECTIVITY
F50/50/62-M 1 100FX, OC3, OC12, Gigabit Dual SC
F50/50/50-M 1 100FX, OC3, OC12, Gigabit Dual SC
F50/50/9-S 1 OC3, OC12, Gigabit Dual SC
PERMAlink ™ Tray
MODEL PORTS TOPOLOGY CONNECTIVITY
8SY-M/62 8 100FX, OC3, OC12, Gigabit Dual SC
8SY-M/50 8 100FX, OC3, OC12, Gigabit Dual SC
8SY-S/9 8 OC3, OC12, Gigabit Dual SC
VERSAtap ™
MODEL PORTS TOPOLOGY CONNECTIVITY
4SY-SX+4C 4 Gigabit Dual SC & LC
WAN
MODEL PORTS TOPOLOGY CONNECTIVITY
DS3AT1 (4) (8) 1 (4) (8) DS3 BNC
DS3-AT 1 DS3 BNC
DS3/E3-PT 1 DS3/E3 BNC
E3-AT 1 E3 BNC
T1/E1-PT 1 T1/E1 RJ48
VERSAlink ™
MODEL PORTS TOPOLOGY CONNECTIVITY
1X4SY-SX+2C 1X4 Gigabit Dual SC & LC
1X8SY-SX+2C 1X8 Gigabit Dual SC & LC
2X4SY-SX+2C 2X4 Gigabit Dual SC & LC
2X8SY-SX+2C 2X8 Gigabit Dual SC & LC
WAN
MODEL PORTS TOPOLOGY CONNECTIVITY
W2358Dsl 2X8 WAN DB15
WX8T1/E1sl 2X8 T1/E1 RJ48
WX16T1/E1sl 2X16 T1/E1 RJ48
D28100BT SL 1x8 • 10/100BaseT and RJ48 •
1x8 WAN DB15
DS3-8Csl 2X8 DS3 BNC
2X4SY-DS3/E3 2X4 DS3/E3 BNC
Compliance Testing
CAUTION: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment.
Certifications
This equipment has been tested and found to meet the radiated and conducted
emission limits for a Class B product of EN 55022 to the EMC Directive
89/336/EEC requirements.
This equipment has been tested and found to meet the immunity levels for
Class 1 tested to level 2 for EN 6100-4-2, tested to level 3 for EN 61000-
4-3, tested to level 2 for EN 61000-4-4, and tested to level 3 for EN 61000-
4-5 to the EN 50082-1 requirements and meets the Class A requirements for
EN 61000-3-2 and EN 61000-3-3.
This equipment has completed the Product Safety Review and found to meet
the Low Voltage Directive 72/23/EEC (1993) requirements.