Denon PMD340 - Manual (Page 21)

17
ENGLISH
FRANCAIS
DEUTSCH
NEDERLANDS
ESP
ANOL
IT
ALINO
POR
T
UGUES
SVENSKA
D
ANSK
D
ANSK
SVENSKA
POR
TUGUES
IT
ALINO
ESP
ANOL
NEDERLANDS
DEUTSCH
FRANCAIS
ENGLISH
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
*15
16
17
*18
19
20
21
Selects the Auto Cue function. If this item is set to "On",
the CD sync function will not work.
Selects the sound level at which the Auto Cue function
operates.
Selects the End Monitor playing time.
Selects the time at which END starts to flash.
Selects the fade-in time.
Selects the fade-out time.
Selects the delay when going from paused to the start
of playing.
Selects the time display mode when the power is turned on.
Enables/disables key lock.
When key lock is "On", only the POWER q and
PRESET !0 buttons function.
Selects whether to enable or disable control buttons during
playback that was initiated using "fader start." During playback,
only the POWERq,TIME u and TEXT i buttons can
be used. All buttons can be used when playback is paused.
Enables/disables the OPEN/CLOSE button while playing.
Selects the auto close time for the disc tray.
Selects the operation that is performed after a disc is loaded
in the disc tray and after a track is selected.
Refer to page 7 for a complete explanation of each setting.
Selects the wait time before the CD player enters auto
standby.
Selects whether to output digital signals or not.
If this item is set to "ON," the instant start, shockproof, and
pitch bend functions will not work.
Enables/disables the Control I/O (D-sub 25-pin) ⁄0 input jack
(PMD331/PMD340) or the fader start input jack (PMD330)c.
Enables/disables the CD Sync function.
Selects whether to output the CD Sync signal through the
RC5 jack b when playback starts.
Turn Auto Cue (preset #1) "Off" to utilize the CD sync function.
Selects which Index (#2 or #3) will trigger an output on
pin #11 on the Control I/O Port.
Selects whether or not to display a warning when a skip
occurs as a result of a bad CD.
Selects the CD-TEXT display language.
Selects whether or not to restore the original presets.
Auto Cue:
AC Lev:
END Mon:
END Warn:
FadeIn:
FadeOut:
Delay:
Time:
KeyLock:
FaderLok:
TrayLock:
AutoCLS:
Start:
AutoSTBY:
D.OUT:
Remote:
CD Sync:
Index:
Alert:
Text:
Reset?:
On
On
5s 10s 15s 20s 25s 30s 35s
5s 0s 10s 15s 20s 25s 30s 35s
Trk REM Dsc ELP Dsc REM Dsc TTL Trk ELP
Pause Play Stop
English French Spanish German
Track
Elapsed Track
Remain Disc
Elapsed Disc
Remain
Disc Total
0ms 100ms 200ms 300ms 400ms
0s to 8.0s in 0.5s Steps
0s to 8.0s in 0.5s Steps
Off
Off
On Off
On Off
On Off
On Off
On
Yes
Off
No
#3 #2
Off
Off 10s 30s 60s 180s
30m 20m 10m
30s 30min 20min 10min
30sec
On
The settings shown in (bold) are the initial settings. LCD Display Presetting items / Function
- 40dB, - 90dB to - 35dB in 5dB Steps
Using the Preset Menu
* Those items marked with an asterisk can only be selected on the PMD331/PMD340. They are not displayed on the PMD330.
Preset Menu Chart: Functions, LCD Display, and Initial Values
Changing the Preset Settings
Procedure
1. Press the button !3 to put the CD player in the stopped
mode.
2. Press the PRESET button !0.
The /ENTER button !7 light.
3. An item that can be set as a preset appears on the display
E. (Refer to the Preset menu table for a list of these items.)
4. Press the PRESET button !0 in order to scroll through the
preset items.
Tip:
It is also possible to scroll through the items by pressing the
INDEX+ button
@4 or the INDEX– button @1 .
5. Use the button !2 or the button !4 to change the
setting of the displayed preset. At this point, the /ENTER
button !7 changes from being steadily lit to flashing.
6. Press the /ENTER button !7 to confirm the selection.
At this point, the /ENTER button !7 changes from being
flashing to steadily lit.
Tip:
Press the CUE/CLEAR button !5 to cancel a setting before it is
confirmed.
Note:
If “D.OUT” is set to “On,” the instant start, shockproof, and
pitch bend functions will not work.
ENTER ENTER
ENTER ENTER