Arcam CR80 - Manual (Page 4)

AMP - ARCAM AMPLIFIERS
The CR80 controls all the functions of the AVR100, AVR200 and AV8 model
AV amplifiers and most of the functions of ARCAM stereo amplifiers. Refer
to the Arcam amplifier product manual for details of each function.
AVR200 and AVR100 Models^ the following keys are active;
- Standby
- Source selection buttons on the numeric keys (note that the 5,1 input is
accessed using the AV key)
- Volume +/-
- Mute
- Mode
- Info
- Cursor and OK keys
- P-, P+ (Preset - y +)
- TM (Tuner Mode)
- TST (Test Tone)
- DYN (Dynamic Range)
-SLP (Sleep)
- TRM (Trim)
AV8 Model: Refer to the handbook for information and use.
Major control functions for the ARCAM DVD players are also available on
the remaining keys, e.g, Play, Stop etc.
Controlling ARCAM AV Components
DVD - ARCAM DVD Players (type DV88, DV27)
All ARCAM DVD commands with exception of slow reverse play are avail­
able on this device page. Refer to your DVD player manual for details of
operation. All keys are labeled for DVD functions except the following;
- Enter/AM
- Last
- Sleep
-CH+
-CH-
- Mode
- Info
Repeat
Slow forward, press Play to exit
Clear
''
Next
Previous
Program
Display
The DVD functions of the bottom 12 keys are labeled above the keys.
CD - ARCAM CD Players
All the primary ARCAM CD commands are available on this device page.
Refer to your CD player manual for details of operation. All keys are
labeled for CD functions except the following;
- Enter/AM
- Last
- Sleep
- CH-
h
-CH-
- Mode
- Info
Repeat
Random
Clear
Next
Previous
Program
Display
AUX - ARCAM AM/FM Tuners
All current Arcam AM/FM tuner commands are available on this page
Refer to your tuner manual for details of operation. The keys operate as
follows;
- 1-8
Use for presets 1-8, and for models T51, T21: pre­
sets 9-16 when held down
- SUB Band change
- CH+ Next preset
- CH- Previous preset
- Mode = Mono/Stereo
NOTE: the Arcam Amplifier AV8 Zone 2. system code 19 can be controlled
from the AUX mode by entering the device code which is specified in the
back of the manual.
PROGRAMMING OTHER
COMPONENTS
The ARCAM CR80 can control up to eight differerit components. Perform
the following instructions for each component you want controlled:
1 Turn on a component (e.g. VCR) and. If applicable, insert media
(e,g„ cassette or disc).
NOTE: Please read steps 2-4 completely before proceeding. We recommend
highlighting or writing down the codes and device you wish to program
before moving onto step 2.
2 On the ARCAM CR80, press a component key once (i.e., CBL, DVD,
VCR, TV, SAT, CD, or AUX). This feature is not applicable for the
AMP key because it has only one dedicated code in this mode for
Arcam amplifiers.
3 Press and hold SET until the LED blinks twice, then release SET.
4 Use the Manufacturer's Codes (in the back of the manual, page
24 ■ 27) to locate the type of component and brand name and then
enter the first four-digit code for your component, tf performed
correctly, the LED will blink twice,
NOTE: if the LED did not blink twice, then repeat steps 2 through 4 and try
entering the same code again.
5 Aim the ARCAM CR80 at the component and press PWR once. It
should turn off. If it does not respond, repeat steps 2-4, trying each
code for your brand until you find one that works, If it still does not
work, try searching for the code (see Searching For Your Code).
NOTE: If the device does not have a PWR key, press PLAY.
6 Repeat steps 1 through 4 for each corriponent you want the ARCAM
CR80 to control.
NOTE: If you want the Arcam AV8 zone 2, system code 19 function, then
this device must be setup under the AUX key only.