MTD 242-662-000 - Manual (Page 8)

PARTS LIST FOR MODE LS 660, 662 AND 242665 POWER VACUUMS
REF.
NO.
PART
NO.
CODE DESCRIPTION
REF.
NO.
PART
NO.
CODE DESCRIPTION
1 749-0664 Upper Handle 26 738-0507B Shoulder Bolt .5" Dia. x 7/16" Lg.
2 — Engine 27 728-0128 Push Cap .5" Rod (Black)
3 710-0260 Carriage Bolt 5/16-18 x .62" Lg.* 28 736-0272 FI-Wash. 1/2" I.D. X 1.0" O.D.
4 15784 638 Blower Housing Ass’y. X .06"
5 710-0654A Hex Tap Scr. 3/8-16 x ' .0" Lg. 29 734-1140 Rear Wheel Ass’y. Comp.
6 15786A Impeller Ass’y- 31 750-0588 Wheel Spacer 1/2" I.D. x 15/16"
7 736-0217 L-Wash. 3/8" I.D.* 34 15779 Air Duct Ass’y.
8 710-0591 Hex Bolt 3/8-24 X 1.0" l.g. 35 710-0201 Hex Bolt3/8-16x.75"*
w/Patch 36 710-0344 Hex Bolt 3/8-16x1.5’’*
9 722-0137 P.V.C. Foam Strip-12" 38 720-0170 Hand Knob
10 15780 638 Vacuum Deck Ass’y. 39 712-0107 Hex L-Nut 1/4-20 Thd.
11 15796 Front Baffle Ass’y. 40 712-0113 Wing Nut 1/4-20 (Plastic)
12 15788 Lower Baffle Ass’y. 41 710-0136 Hex Bolt 1/4-20 X 1.75"*
13 15790 Wiper Retaining Strip 42 764-0208A Vacuum Bag (6.6 Bushel)
14 728-0123 Pop Rivet .188" Dia. 43 749-0592 Lower Handle
15 735-0222 Nozzle Wiper Rear 44 14578 Height Adj. Ass’y. Comp.-R.H.
16 712-0267 Hex Nut 5/16-18 Thd.* 14579 Height Adj. Ass’y. Comp.-L.H.
17 736-0242 Bell-Wash. .34" I.D. x .fi7" O.D. (Not Shown)
18 738-0102 Shid. Bolt .498" Dia. x 1.45" Lg. 45 1539-019 Push Speed Nut .25" Dia.
19 734-1139 Front Wheel Ass’y. Conp. 46 711-0737 Stud Pin .25" Dia. x 1.75" Lg.
20 736-0331 Bell-Wash. .39" I.D. x 1 12" O.D. 47 714-0105 Sq. Key 3/16" X 1" Lg.
21 15262B Wheel Pivot Bar 48 735-0221 Nozzle Wiper Side
22 15261A Index Plate 49 15789 Wiper Retaining Strip
24 712-0798 Hex Nut 3/8-16 Thd.* 50 710-0302 Hex Self-Tap Scr. #10
25 14832 Spring Lever Ass’y. w/H ,nob 51 736-0169 L-Wash. 3/8" I.D.*
'For faster service obtain standard nuts, boits and washe s iocaliy.
If these items cannot be obtained locaiiy, order by par: number
and size as shown on parts list.
(638—Red) (498—Yeiiow)
CODE; N notates a new part (not previousiy existing). A three digit
number is the color code. Specify coior code if coior or finish is
important when ordering parts, [i.e., (part no.)-638 for Red
Finish].
TROUBLE SHOOTING
PROBLEM POSSIBLE CAUSE(ii) CORRECTIVE ACTION
Engine fails to start 1 . Fuei tank empty, c r stale fuel.
2. Spark plug wire disconnected.
3. Faulty spark plug.
1 . Fill tank with clean, fresh fuel.
2. Connect wire to spark plug.
3. Clean, adjust gap or replace.
Loss of power;
operation erratic 1 . Spark plug wire loi >se.
2. Blocked fuel line (i ’ so equipped)
or stale fuel.
3. Water or dirt in fue 1 system.
4. Carburetor out of < idjustment.
5. Dirty air cleaner.
1 . Connect and tighten spark plug wire.
2. Clean fuel line; fill tank with clean
fresh gasoline.
3. Disconnect fuel line at carburetor to drain fuel
tank. Refill with fresh fuel.
4. Adjust carburetor.t
5. Service air cleaner.f
Engine overheats 1 . Carburetor not adj jsted
properly.
2. Engine oil level lov/.
1. Adjust carburetor.t
2. Fill crankcase with proper oil.
Too much vibration
. — /
Loose parts or dar laged
crankshaft. Stop engine immediately and disconnect
spark plug wire. Tighten all bolts and nuts.
Make all necessary repairs. If vibration continues,
have unit serviced by an authorized service
dealer.
Unit does not X
discharge /
1. Directional dischaige clogged.
2. Foreign object lodijed in air vane
plate assembly.
1. Stop engine immediately and disconnect
spark plug wire. Clean directional discharge.
2. Stop engine immediately and disconnect
spark plug wire. Remove lodged object.
tRefer to the engine manual packed with your unit.
NOTE: Fo/repairs beyond the minor adjustments listed above, please contact your nearest authorized service dealer.
FOR REPLA CEMENT PARTS, CONTACT:
SERVICE DEPARTMENT • FlO. BOX 360900 • CLEVELAND, OHIO 44136