MTD 219-405-000 - Manual (Page 17)

M odel 405
PARTS LIST FOR MODEL 405 ROTARY TILLER
HEF.
NO.
PART
NO.
CODE DESCRIPTION
REF.
NO.
PART
NO.
CODE DESCRIPTION
1 710-0528 Hex Bolt 5/16-18 X 1V4" Lg.* 48 712-0267 Hex Nut 5/16-18 Thd.*
2 720-0180 Grip 49 736-0119 L-Wash. 5/16" I.D.*
5 710-0458 Carr. Bolt 5/16-18 x 1.75"* 50 14975 638 Frame Rail—L.H.
7 784-0031 Clutch Grip Ass’y.—L.H. 51 726-0175 Clamp 5/16" Dia.
(Tines) 52 736-0119 L-Wash. 5/16" I.D.*
9 15093C Clutch Cable Bracket 53 712-0267 Hex Nut 5/16-18 Thd.*
10 710-0607 Hex Wash. S-Tap Scr. 54 710-0118 Hex Bolt 5/16-18 X 3/4" Lg.*
5/16-18 X .62" Lg. 55 720-0165 Ball Knob 1V4" Dia.
11 712-0256 Hex Nut 5/16-24 Thd. 56 736-0169 L-Wash. 3/8" I.D.*
12 736-0119 L-Wash. 5/16" I.D.* 57 712-0798 Hex Nut 3/8-16 Thd.*
13 746-0484 Wheel Drive Cable 58 710-0118 Hex Bolt 5/16-18 X .75" Lg.*
14 712-0267 Hex Nut 5/16-18 Thd.* 59 15393 Brkt. Reinforcement
15 736-0119 L-Wash. 5/16" I.D.* 61 784-0026 Tine Shield Ass’y.
16 784-0036A N Handle Panel 62 714-0149 Hairpin Cotter
17 749-0637 Handle—-L.H. 63 711-0415 Clevis Pin 3/8" Dia.
18 712-0798 Hex Nut 3/8-16 Thd.* 64 749-0762 Handle—R.H.
19 736-0169 L-Wash. 3/8" I.D.* 65 720-0195 Hand Knob
20 736-0105 Bell-Wash. 3/8" I.D. 66 714-0127 Cotter Pin 1/16" Dia. x .75" Lg.*
21 710-0253 Hex Bolt 3/8-16 X 1.00" Lg.* 67 712-0375 Hex Cent. L-Nut 3/8-16 Thd.
22 714-0507 Cotter Pin 3/32" Dia. x 3/4"* 68 784-0270 Clutch Grip Ass’y.—R.H.
23 725-0157 Cable Tie (Wheels)
24 747-0432 Tiller Flap Rod 69 738-0560 Shoulder Bolt .38" Dia. x
25 14989 End Cover Ass’y —L.H. 1.53" Lg.
14990 End Cover Ass’y.—R.H. 70 741-0402 Hex Flange Plastic Bearing
(Not Shown) 71 738-0561 Shoulder Nut V4-20 Thd.
736-0242 Bell-Wash. 5/16" I.D. 72 746-0502 Throttle Control Wire
,7 712-0267 Hex Nut 5/16-18 Thd.* 73 831-0823A N Throttle Control Box Ass’y.
28 15390 638 Side Shield 74 736-0219 Bell-Wash. .40" I.D.
29 15397 L.H. Tine Ass’y. Comp. 75 784-0022 Handle Pivot Bracket
15398 R.H. Tine Ass’y. Comp. 76 738-0281 Shoulder Bolt
(Not Shown) 77 784-0019 Handle Mtg. Bracket
30 712-0241 Hex Nut 3/8-24 Thd.* 78 784-0025 Adj. Handle Ass’y.
31 736-0169 L-Wash. 3/8" I.D.* 79 712-0375 Hex Cent. L-Nut 3/8-16 Thd.
32 710-0191 Hex Bolt 3/8-24 X 1.25" Lg.* 80 736-0105 Bell-Wash. .40" I.D. x .88" O.D.
33 714-0149 Hairpin Cotter 81 736-0253 Bell-Wash. Vz" I.D. x 1.00" O.D.
34 14978 Tine Adapter Ass’y. 82 711-0765 Lock Pin 5/16" Dia. x 8"
35 742-0106 Tine 12" R.H. 83 784-0023 Lower Sliding Ass’y.
36 742-0105 Tine 12" LH. 84 736-0463 FI-Wash. .291" I.D. x .62" O.D.
37 711-0415 Clevis Pin 3/8" Dia. 85 732-0145 Compression Spring .36"
38 712-0267 Hex Nut 5/16-18 Thd.* O.D. X 1.00" Lg.
39 736-0119 L-Wash. 5/16" I.D.* 86 738-0147 Shoulder Bolt Vz" Dia. x
40 14979 Tine Shield Flap .170" Lg.
41 710-0736 Hex Bolt 5/16-18 X 1.0" Lg.* 87 710-0599 Hex Wash. S-Tap Scr. V4-20
42 738-0507B N Shid. Bolt V 2 " Dia. x .426"
X .50" Lg.
43 736-0117 FI-Wash. 3/8" I.D. x 5/8" O.D. 88 736-0242 Bell-Wash. 5/16" I.D.
44 710-0216 Hex Bolt 3/8-16 X 3/4" Lg.* 89 736-0285 FI-Wash. 5/8" I.D.
45 14992 Depth Bar Ass’y. 90 710-0779 Self-Tap Scr. #10 x Vz" Lg.
46 712-0267 Hex Nut 5/16-18 Thd.* 91 746-0535 Tine Control Cable
47 736-0119 L-Wash. 5/16" I.D.*
*For faster service obtain standard nuts, bolts and washers locally.
If these items cannot be obtained locally, order by part number and
size as shown on parts list.
CODE: N notates a new part (not previously existing). A three digit
number is the color code (use if color or finish Is important when
ordering parts). See chart below, [i.e., (part no.)-638 for Red Finish].
Color Codes
460—Green Flake 630—Blue
483—Charcoal Grey 635—Grey
498—Yellow 636—White
499—Beige 637—Black
606—Orange 638—Red
629—Silver Flake 640—Green
17