MTD 243-540 - Manual (Page 3)

PARTS LIST FOR 243-540 EDGER
Ref.
No.
Part
No.
Color
Code
Description
New
Part
Ref.
No.
Part
No. Color
Code
Description
New
Part
1 720-142 Flat Bar End Grip 39 736-329 Spring Lockwasher 1/4" Scr. *
2 9948 Clutch Flandle Assembly 40 710-179 Hex F—Tapp. Scr.1/4—20 x .50 " Ig.
3 10229 Spindle Flousing Ass'y. Comp. 41 9944-463 Belt Guard Assembly
(Inch Ref. Nos.36, 42, 43, 44, 45) 42 9934 Spindle Housing Ass'y.
4 714-115 Cotter Pin 1/8"Dia. x 1.00"lg.* 43 711-385 Spacer .690 I.D. x .810 O.D.x 2.060 Ig.
5 710-106 Flex Fid.Cap Scr.1/4—20 x 1.25"lg.* 44 741-124 Ball Bearing
6 9950 Clutch Plate 45 711-384 Spindle
7 732-171 Compression Spring .50 O.D.x 1.40"lg. 46 736-116 Flat Washer .635 I.D. x .93 O.D.
8 736-264 Flat Washer .344"!.D. x .62" O.D. 47 715-246 Spring Pin Spirol
9 712-158 Hex Center Locknut 5/16—18 Thd. 3/16" Dia. X 1.25" Ig.
10 9951 Clutch Rod 48 711-420 Sheave
11 Engine 49 736-105 Belleville Washer .400 I.D. x .88 O.D.
12 714-105 Sq. Key 3/16 X 1.00" Ig. 50 734-481 6 inch Wheel Assembly - front N
13 711-421 Sheave 51 738-213 Shoulder Screw .498"Dia. x 1.450
14 736-114 Internal Lockwasher 1/2" Scr. * 52 712-267 Hex Nut 5/16-18 Thd. *
15 710-121 Hex Hd. Cap Scr. 53 736-119 Spring Lockwasher 5/16"Scr. *
1/2—20 X .75" Ig. Special 54 711-386 Spacer .386 I.D.x.510 O.D.x 3.765
16 9941-463 Belt Guard Ass'y. 55 715-247 Spring Pin Spirol 3/16"Dia.x 1.00"lg.
17 748-227 Hex Flange Bearing .630 I.D.Bronze 56 732-188 Torsion Spring
18 710-137 Set Scr.5/16—24 x .32 Cone 57 715-101 Spring Pin Spirol 1/4"Dia.x 1.50" Ig.
19 710-442 Hex Hd.Cap Scr. 58 712-107 Hex Center Locknut 1/4—20 Thd.
5/16-18 X 1.50" Ig. * 59 738-108 Shoulder Screw .498" Dia. x 1.450
20 754-142 3V Belt 31.2" Ig. 60 734-480 7 inch Wheel Assembly — Rear N
21 710-402 Hex Hd. Cap Scr. 61 736-169 Spring Lock Washer 3/8" Scr. *
5/16-18x4.50" Ig. * ■ 62 712-798 Hex Nut 3/8-16 Thd. *
22 711-379 Bushing 63 12264-463 Base Assembly - complete N
23 732-187 Compression Spring 64 749-126 Lower Handle N
24 9932 Pivot Bracket Ass'y. 65 746-145 Cable Clip
25 9946 Lever Assembly 66 710-111 Carriage Bolt 1/4-20 x 1.25"lg.*
26 736-112 Belleville Washer .535 I.D. x 1.50 O.D. 67 712-287 Hex Nut 1/4-20 Thd. *
27 712-114 Finished Slotted Hex Nut 1/2—20 Thd. 68 732-200 Conduit and Wire — Throttle Control
28 9952 Guide 69 711-178 Pivot Bushing — Throttle Control
29 712-267 Hex Nut 5/16-18 Thd. * 70 10006 Bracket Ass'y. — Throttle Control
30 736-119 Spring Lockwasher 5/16" Scr.* 71 710-606 Hex Hd. Cap Scr.
31 9938 -463 Guard Assembly 1/4-20 X 1.50" Ig. *
32 9954 Blade 72 7470 Knob — Throttle Control
33 712-200 Hex Inserted Lock Nut 1/2—20 Thd. 73 712-107 Hex Center Lock Nut 1/4—20 Thd.
34 736-112 Belleville Washer 74 10449 Throttle Control Assembly - complete
.535" I.D. X 1.50" O.D. 75 736-329 Spring Lock Washer 1/4" Scr.*
35 712-922 Hex Jam Nut 1/2-20 Thd. 76 749-127 Upper Handle N
36 741-124 Ball Bearing
37 10244 Clamp Bracket
38 710-276 Carriage Bolt 5/16—18 x 1.00" Ig. *
*For faster service order standard nuts, bolts, and washers locally. If these items cannot be obtained locally, order by
part number and size as shown on parts list.
(463 — Top Flite Red) — When ordering parts, if color or finish is important, use the appropriate color code shown at
left. (e.g. Top Flite Red 9938 (463)).
The engine is not under warranty by the
edger manufacturer. If repairs or service is
needed on the engine, please contact your
nearest authorized engine service outlet.
Check the "Yellow Pages" of your
telephone book under "Engines —
Gasoline." Find usfastintha