Ryobi CS30 RY30923 - Manual (Page 3)

SPECIFIC SAFETY RULES
SPECIFIC SAFETY RULES FOR TRIMMER
USE
■ Replace string head if cracked, chipped, or damaged
in any way. Be sure the string head or blade is properly
installed and securely fastened. Failure to do so can cause
serious injury.
■ Make sure all guards, straps, deflectors, and handles are
properly and securely attached.
■ Use only the manufacturer’s replacement string in the
cutting head. Do not use any other cutting attachment.
To install any other brand of replacement string or cutting
head to this string trimmer can result in serious personal
injury.
■ Never operate unit without the grass deflector in place
and in good condition.
■ Maintain a firm grip on both handles while trimming. Keep
string head below waist level. Never cut with the string
head located over 30 in. or more above the ground.
SPECIFIC SAFETY RULES FOR BRUSH-
CUTTER AND BLADE USE
■ After engine stops, keep rotating blade in thicker weeds
or pulpy stalks until it stops.
■ Do not operate the brushcutter unless the brushcutter
guard is firmly secured in place and in good condition.
■ Use heavy gloves when operating the brushcutter and
when installing or removing blades.
■ Always stop the engine and remove the spark plug wire
before attempting to remove any obstruction caught or
jammed in the blade or before removing and installing
the blade.
■ Do not attempt to touch or stop the blade when it is
rotating.
■ A coasting blade can cause injury while it continues
to spin after the engine is stopped or throttle trigger
released. Maintain proper control until the blade has
completely stopped rotating.
Replace any blade that has been damaged. Always make
sure blade is installed correctly and securely fastened
before each use. Failure to do so can cause serious
injury.
Use only the manufacturer’s replacement Tri-Arc® blade
intended for use on this brushcutter. Do not use any other
blade. To install any other brand blade or cutting head to
this brushcutter can result in serious personal injury.
The Tri-Arc® blade is suited for cutting thicker weeds or
pulpy stalks only. Do not use for any other purpose. Never
use the Tri-Arc* blade to cut woody brush.
Exercise extreme caution when using the blade with this
unit. Blade thrust is the reaction that may occur when
the spinning blade contacts anything it cannot cut. This
contact may cause the blade to stop for an instant, and
suddenly “thrust” the unit away from the object that was
hit. This reaction can be violent enough to cause the op­
erator to lose control of the unit. Blade thrust can occur
without warning if the blade snags, stalls, or binds. This is
more likely to occur in areas where it is difficult to see the
material being cut. For cutting ease and safety, approach
the weeds being cut from the right to the left. In the event
an unexpected object or woody stock is encountered, this
could minimize the blade thrust reaction.
I Never cut any material over 1/2 in. diameter.
I Always wear the shoulder harness when using the brush-
cutter and adjust to a comfortable operating position.
Maintain a firm grip on both handles while cutting with a
blade. Keep the blade away from your body and below
waist level.
I Never use the brushcutter with the blade located 30 in,
or more above the ground level.
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning for safe
operation of this product.
SYMBOL NAME EXPLANATION
A Safety Alert Precautions that involve your safety.
Read the Operator’s Manual
To reduce the risk of injury, user must read and under­
stand operator’s manual before using this product.
0
Wear Eye and Flearing Protection
Wear eye protection which is marked to comply
with ANSI Z87.1 as well as hearing protection when
operating this equipment.
Keep Bystanders Away Keep all bystanders at least 50 ft. away.
A Ricochet
Thrown objects can ricochet and result in personal injury
or property damage.
No Blade
Do not install or use any type of blade on a product dis­
playing this symbol.
A
Blade Thrust
Beware of blade thrust. Products authorized for blade use
will display this symbol to warn of blade thrust.
Gasoline and Oil
Use unleaded gasoline intended for motor vehicle use
with an octane rating of 87 [(R + M) / 2] or higher. This
product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle oil.