SINGER 114-31 - Manual (Page 14)

;8 NUMERICAL LIST OF PARTS
No. Plate Name No. Plate
27739 23160 Thread Unwinder Thread Cone (wood) for 50446D 9596
large cones for 225260....................................... 51120J 9596
32675 23164 Presser Bar Spring......................................................
34418 23161 Looper Washer for 124899........................................ 51188J 23166
39216 23159 Table Belt Guide with two 168E, for
39221.................................................................... 51591J 9596
39219 23159 Table Belt Guide Pulley Shaft (long)wlth
17896 and 63973, for 39221............................... 51224W 9596
39220 23159 Table Belt Guide Pulley Shaft (short) 51224J 23177
with 17896 and 63974, for 39221....................... 51387R 23161
39221 23159 Table Belt Guide complete. Nos. 17892, 51857 23161
39219,39220,two each 17893,39218 and
three wood screws 1 1/4 in. No. 12.. 52045 23161
39222 23153 Belt Shifter for 124771................................................
39408 Presser Bar Lifting Lever Rod 17845 with 55300 23175
17846....................................................................
39452 23164 Thread Wiper Body for 136556................................. 56015 23161
39453 23164 " " " Finger for 59807............................................ 56493 9596
39455 23164 " " " Wire for 136556............................................ 56549
39456 23164 " " " " Clamp for 136556.
41635 2.'3160 ” Unwinder Thread Guide Bracket with 56864 23159
175E, for 60772................................................... 56865 23159
42336 23166 Tension Spring............................................................. 59702 23161
42639 23164 Needle Bar Thread Retainer Position Pin 59703 23161
for 124796............................................................ 59704 23161
42808 23164 Thread Take-up Roller for 124626............................ 59705 23161
50016F 23176 Knife Holder Cap Screw for 124877......................... 59706 23161
5014 fC 23166 Tension Screw Stud for 124687................................. 59707 23161
50150C 23161 Looper Shaft Coupling Set Screw for
124765.................................................................. 59707 23161
50150C 23161 Thread Nipper (upper) Cam Set Screw for 59708 23161
59774....................................................................
50152D 9596 Knife Bar Check Screw.............................................. 59710 23164
50165J 23158 Eye and Finger Guard Frame Screw for 59711 23164
121613.................................................................. 59712 23164
50169G ;i3161 Looper Shaft Bushing Set Screw...............................
50222K 23158 Eye and Finger Guard Carrying Arm Hinge
Screw (front) for 121613.................................... 59730 23175
IX0274C 23161 Looper Set Screw for 124885..................................... 59734 9596
50306D 23175 Feed Plate Carrier Bar Pivot Block Screw
50333C 23161 Arm Shaft (horizontal) Bushing (back) 59735 9596
Adjusting Screw.................................................
50370J 23166 Tension Thread Guide Set Screw.............................. 59739 23176
50372D 23153 Stop Cara Interlocking Rod Case Bracket 59739 23176
Screw................................................................... 59747 ;i3i6i
50435J 9596 Brake adjusting Plate Handle Hinge Screw 59757 23161
50435K 23158 Eye and Finger Guard Depressing Screw
for 121627............................................................ 59761 23161
50435K 23158 Eye and Finger Guard Guiding Rod Hinge 59765 23161
Screw for 121613................................................ 59766 23161
NUMERICAL LIST OF PARTS 39
Name
Bx'ake Hinge Screw....................................................
Knife Bar Check Regulating Screw for
124936..................................................................
Thread Nipper (lower) Lever Shaft Brack­
et Screw...............................................................
Knife Bar Check Regulating Screw Lock
Nut for 124936....................................................
Brake Adjusting Plate Thumb Screw........................
Clamp Cuff Guide Thumb Screw for 124922.
Pulley (loose) Cap Screw for 68717............................
Needle Guard Shaft Crank Roller for
124974..................................................................
Looper Driving Shaft Bushing Packing
(cotton)................................................................
Feed Plate Carrier Bar Position Plate
Steady Pin for 62123...........................................
Arm Oil Tube for oiling 59705 and 59706.
Brake Pad (leather) for 124713..................................
Thread Controller Stud Collar Pin for
124610..................................................................
Chain Hook (large) for 13351.....................................
" " (small) for 13351.....................................
Arm Shaft (horizontal)................................................
" " " Gear with two 1036C
Arm Shaft (upright)....................................................
” " " Bushing (lower).................
" " " " (upper).............
" " " Gear (lower) with two
1253C...................................................................
Looper Driving Shaft Gear with two 1253C
Arm Shaft (upright) Gear (upper) with
two 1253C............................................................
Clamp Lifter for 59807...............................................
Face Plate for 59712....................................................
Face Plate complete, Nos.208J,9544,9545,
59711 and two each 229J, 2107 and
9543......................................................................
Feed Plate Carrier Bar Pivot Block...........................
Knife Bar Driving Lever with 223F and
59735....................................................................
Knife Bar Driving Lever Lock Stud for
59734....................................................................
Knife Holder Cap Stud for 62129..............................
" " Stud for 62128......................................
Looper Driving Shaft Gear Cover.............................
Needle Bar Crank Wheel with 448C and
1293C...................................................................
Needle Guard Shaft Collar with two 465C .
" " " Spring.......................................
" « >' " Collar with 624C