SINGER 147-30 - Manual (Page 20)

'10 NUMERICAL LIST OF PARTS
NO. I-LATl-;
5-1048 8964
5-1049 9873
51055 9874
.5-10.56 —
51057 9874
.510,58 —
540,59 —
,51060 —
5-106)1 986)9
51079 —
51080 9876
51088 —
51089 —
51090 —
,5-1103 9873
,51104 9880
54105 8901
,5-1108 —
.54109 —
,54110 9870
54111 8902
*,5-1112 —,—
51113 —
,54218 8904
,54227 9869
,54228 9869
54229 9876
NAMK
Tension (iii)])ei' tlireud) Releasing Shaft
Crank Link.....................................................
Thread (under) Take-up Sta[)le Bracket
with dliOo......................................................
■Cloth Plate Slide (right) for 5-1050..................
Cloth Plate Slide (right) coni|)lete for
51t)51), Nos. 5811!), 51t)55 and two 725 1
Cloth Plate Slide (right) for 51058.....................
Cloth Plate Slide (right) eonipleto for
54000, Nos. :!8119, 51057 and two 725 1
Cloth Plate complete, for in. and in.
gauges, h)r 08010, for 1-17-30 Machine,
Nos. 51011, 54013 and 54050.......................
Cloth Pl.-itc coinidete, for pg in. and in.
gauges, for 08t)lt), for 1-17-30 .Maohine,
Nos. 54011, 54013 and 510.58......................
Looper Holder with IPdOo and ll‘17c. . . .
Arm Rock Shaft 5-1002 with 51t)0-l, 54t)t)5
and ti l255......................................................
Looper Driving Shaft and I'eed Lifting
Eciaaitric Biacket Bushing............................
Crank t'onnecting Hod 54017 with 50009,
for 54384 and 08111......................................
Arm Rotary Shaft Bu.shing (intermediate)
510t»7 with (i l.5t)8 and ti-1805....................
.-\rm Rotary Shaft Flanged Bu.shing 51009
with 5S039 and 0-1805...................................
Pre.sser Bar Lifting Lever Extension,
ohsole.l e........................................................
Cloth Plate Thread Cuard...................................
,\rm Rock Shaft Flanged Bu.shing (front)
Oil Tube for ,51110...........................................
“ “ Bracket for suit)....................................
Oil Tube coni|)lete, for oiling Crank
Connecting Rod (ujiper bearing). Nos.
49092, 54108 and 51109................................
Feeil Connecting Rod with 1057ii, ,51112
and t^vo 800i-:, for 54113..............................
Feed Connecting Rod Cap for 51111.................
“ “ “ ,54111 with 5402,5,
for 54384 and 68111......................................
Crank Connecting Rod Oil Pad (braided
cotton) for 54017...........................................
Looper Carrier Connection for 5-1383...............
“ “ “ Shaft for 54383
“ “ “ “ Bu.shing
NUMERICAL LIST OF PARTS 41
NO. PUATE NAME
5-1230 9869 Ijooper Carrier Driver with 54032 and
four 175 e , for 54383.......................................
542-12 9870 Slack Thread Controller Clamp.............................
54321)
8961 Needle Bar Connecting Link for 54329.. .
54327 8961 “ “ “ “ Hinge Stud
for ,54329.......................................................
54328 8961 Needle Biir Connecting Stud with 21I f
and two 187 e , for ,54329 ..............................
,51329 -------- Neolle Bar Connecting Link 54326 with
5-1327 and 54328...........................................
5-1330 9871 Thread (upper) Controller.........................................
54356) 8980 Belt Cuanl with 1192i', for 54358, obsolete
54357 898t) Machine Base with 1192c, for 54358,
obsolete...........................................................
,51358 -------- Machine Ba.se with Belt Guard complete,
Nos. 27347, 49123, 54356, 54357, 60884,
three each 6055, 51072 e and four each
948 e and 57285, obsolete...............................
5431)7 8985 .\rm Rotary Shaft Bushing (front).............................
*51368 8961 Looper Driving Shaft and Feed Lifting
Eccentric with 227n and two 64315, for
54383..............................................................
N ote ; When No. 54368 is required for repairs, the Arm
Rotary Shaft must be returned to the factory
to be adjusted to the new part.
Slack Thread Controller......................................
Looper Driving Shaft and Feed Lifting
Eccentric 54308 wdth 54027, 54227,
54228 and 54230, for 54384 and 68111
Arm Rotary Shaft 54006 with 640n, 54008,
5-1088, 54113, 54383, 64351 and 04355,
tor 147-30 Machine........................................
Face Plate............................................................
“ “ Thread Guard.....................................
Feed Bar with 50429c and two 453c, for
68022..............................................................
Feed Dog, 22 teeth (14 teeth to the inch)
for 68010........................................................
Looper (back) closed eye....................................
“ (front) closed eye. for 68015......................
“ (intermediate) closed eye, for68015
Needle Bar complete, Nos. 64319 and
128215............................................................
Needle Guard, for A in. to A in. gauges
between each needle.......................................
54381 9870
54383 -----
----
.51381 —
54486 9874
54-187 9871
54488 9874
54489 9875
54490 9869
54491 9869
54492 9869
54493 —
54494 9872