Cen-nvs100, Network video streamer, Adding the cen-nvs100 to your crestron system – Crestron electronic CEN-NVS100 User Manual

Page 2

CEN-NVS100

Network Video Streamer

www.crestron.com

888.273.7876

201.767.3400

QUICKSTART DOC. 6746A (2022586) 03.09

Adding the CEN-NVS100 to Your Crestron System

To add the CEN-NVS100 to your Crestron system, perform the steps in Option 1 or Option 2:

● Option

1 uses VisionTools

Pro-e (VT Pro-e) programming and provides streaming video capabilities only.

●

Option 2 uses both SIMPL Windows and VT Pro-e programming and provides the following capabilities: streaming video, touchpanel control of PTZ cameras, control system response for digital I/O, motion detection, and video detection.

Sample TPMC-8X IP Address and HTTP Command Serial Joins

Sample TPMC-8X Port Number Analog Join

Option 2: SIMPL Windows and VT Pro-e Programming

SIMPL Windows Programming:

A. From

the

Ethernet Control Modules | Ethernet Video Modules folder of the Device Library,

drag the CEN-NVS100 into the System Views.

B. Double-click the CEN-NVS100 in the system tree to open the “Device Settings” window,

and then set the IP address of the CEN-NVS100 (use the IP address set in section , step D2).

If desired, also change the IP

ID of the CEN-NVS100.

C. In

the

Logic folder of

Program View, select the

Built In Programming for

CEN-NVS100 subfolder.

D. In

the

Detail View, enter data

into the following text boxes:

●

Root_Password (use the

root password entered

in section , step C2)

●

Viewer_Name (use the name

entered in section , step C4)

●

Viewer_Password (use the

password entered in section ,

step

C4)

●

IP_ID (use the IP ID assigned

to the CEN-NVS100)

Device Library and Sample System Views

Connect the CEN-NVS100 module outputs (Video_Server_Port_Number,
HTTP_Command_Stream_1, Video_Server_IP_Address, and all others required
for your application) to the touchpanel definition.

VT Pro-e Programming:

A. For the desired touchpanel in
the

ProjectView tab, open the

Embedded

Applications folder

and then double-click

MJPEG

Viewer

to open the

“MJPEG Viewer Embedded

Application

Properties”

window.

B. Click

the

Camera Controls tab.

C. In

the

IP Address, Port #,

and

HTTP Command panes,

set the join numbers using

the same numbers assigned

in step E (above) of the

“SIMPL

Windows

Programming”

section, and then click OK.

D. Save the project.

“MJPEG Viewer Embedded Application Properties” Window

Option 1: VT Pro-e Programming Only

A. For the desired touchpanel in the ProjectView tab, open the Embedded

Applications folder and then double-click MJPEG Viewer to open the
“MJPEG Viewer Embedded Application Properties” window.

B. Click

the

Camera Controls tab.

C. Enter the IP address, port number, and HTTP command into the

appropriate fields, and then click OK.

D. Save the project.

NOTE: For the HTTP command, enter the viewer name and viewer password
assigned when creating a Viewer user account in section , step C4 of
this guide. For example, if the viewer name is MyViewer and the password is
viewmycamera, enter the following:

/video.mjpg?user=MyViewer&pw=viewmycamera

CEN-NVS100 Module Parameters

“MJPEG Viewer Embedded Application Properties” Window

All brand names, product names and trademarks
are the property of their respective owners.