SINGER 147-4 - Manual (Page 3)

INSTRUCTIONS FOR ORDERING
In ordering from this list, use CttiLY the part NUMBER In the
FIRST column.
The number stamped on a Sewing Machine Part Is In every case
the number of the single part only.
Every combination of parts sent out as such has its specific
number, which, although not stamped on the parts, must be used
when ordering the combination.
Each number always Indicates the SAME PART In whatever list
It appears, or for whatever machine.
Tho letters after some of the numbers Indicate the style of
finish only, as follows:
A-Hardened, Pollslied, Nickel Plated and Buffed
A.A-Buffed and Chromium Plated
A.B-Hardened, Polished, Buffed and Chromium Plated
A.C-Brown Baking Enaifvjl Finish
A.D-aray Baking Enamel Finish
A.E-Hardened, Bright Rumbled and Nickel Plated
A.F-Hardened, Bright Rumbled, Nickel Plated, Bright Rumbled and
Chromium Plated
B-Polishod, Nickel Plated and Buffed
C-Hardened Only
C.R-Hardened and Merllzed
D-Pollshed Only
E-Soft, Not Polished
F-Hardened and Polished
F.J-Hardoned, Polished and Nickel Plated
G-Brlght Rumbled and Nickel Plated
H-Blued
J-NIckel Plated Only
K-Hardened and Nickel Plated
L-Brass Plated
M-Oxldlzed
N-Japanned, Dull
P-Japanned, Bright
P.P-Wrlnkle Finish
R-Merllzed
S-Cadmium Plated
T-Copper Plated
T.A-Hardened, Polished, Copper and Nickel Plated and Buffed
T.B-Copper and Nickel Plated and Polished
T.J-Coppor and Nickel Plated Only
T.K-Hardened, Copper and Nickel Plated
T.L-Copper and Brass Plated
T.M-Copper Plated and CKldlzed
U-21nc Plated
V-Sllver Plated
W-Pollahed and Nickel Plated
X-Black Oxide, for Iron and Steel
X.C-Hardened and Black Oxide, for Iron or Steel
Y-Black Nickel Plated Ckily
Z-Chromlum Plated
Z.A-Hardened,Pollstiod,Nickel Plated,Buffed and Chromium Plated
Z.B-Polished, Nickel Plated, Buffed and Chromium Plated
Z.C-Hardened and Chi’omlum Plated
Z.D-Poilshed and Chromium Plated
Z.Q-Brlght Rumbled, Nickel Plated, Bright Rumbled and Chromium Plated
Z.J-NIckel and Chromium Plated
Z.T-Copper and Chromium Plated
These letters MIX.>T BE USED when they appear in the list; and
AFTER the number as In the Hat.
In this series:
1 to 1500, 50001 to 51500 and 140001 to 142000
are Screw Numbers
1501 to laOO and 51501 to 51800 are Nut Numbers
1601 to 2000 and 51901 to 52000 are Holler Numbers
2001 to 50000 and 52001 to 140000 and 142001 to
190000 are Sewing Machine Parts, 190001 and upward
are numbei’s of Electrical Parts,
The figures In tlie second column refer only to the plates,
Illustrating the parts, and ai*e NOT TO BE USED In ordering.
Parts marked with an asterisk (*) are furnished only when
repairs are made at factory.
LIST OF PARTS COMPLETE
FOR
MACHINE No. 147-4
For Stitching Button Stays on Knit Underwear. One needle,
one looper. Transverse Binder. Gathering feed. Speed up to
3500 R. P. M., according to the material being stitched.
No. Plate Name
*54304 Arm
,
upper and lower (solid) with 948J,
15404 , 54034 and two 15405..............................
42366 20622 Arm Oil Pad (braided cotton) for oiling
Arm Rock Shaft Front Bearing..........................
56006 20622 Arm Oil Pad (braided cotton) for oiling
Arm Rock Shaft Intermediate Bearing.
56003 20622 Arm Oil Tube with 52045, for oiling
Needle Bar Connecting Link..............................
52045 20622 Arm Oil Tube Packing (wick).....................................
54002 20622 <1 Rock Shaft............................................................
54079 N " " 54002 with 54004 and 64255
64386 20622 u " " Bushing (back)..........................................
4460 20622 *' "
" "
" Set Screw..
64388 20622 tl
" ” "
(Intermediate)....
423C 20622
“ “ "
Set
Screw
..............................................................................................................................