SINGER 116-1 - Manual (Page 3)

INSTRUCTIONS FOR ORDERING
In ordering from this list, use ONLY the part NUMBER
in the FIRST column.
The number stamped on a Sewing Machine part is in every
case the number of the single part only.
Every combination of parts sent out as such has its specific
number, which, although not stamped on the parts, must be
used when ordering the combination.
Each number always indicates the SAME PART in whatevei
list it appears, or for whatever machine.
The letters after some of the numbers indicate thd style of
finish only, as follows;
A. Hardened, Polished and Plated.
Polished and Plated
Hardened only.
Polished only.
Soft, not Polished.
Hardened and Polished. B.
C.
D.
E.
F.
G.
H.
J.
K.
L.
M.
P
R.
Blued.
Plated only.
Hardened and Plated.
Brass or Gilt.
Oxidized.
Japanned.
Parkerized
These letters MUST BE USED when they appear in the list,
and AI'TER the number as in the list.
In this series
1 to 1500 and 50001 to 51500 are Screw Numbers.
1501 to 1800 are Nut Numbers.
1801 to 2000 are Roller Numbers.
2001 to 50000 and 52001 and upward are numbers of
Machine Parts.
The figures in the second column refer only to the plates,
illustrating the parts, and are NOT TO BE USED in ordering.
Parts marked with an asterisk (*) are furnished only when
repairs are made at factory.
LIST OF PARTS COMPLETE
FOR
MACHINE No. 116-1
FOR SNAPPING THE ENDS OF BINDING, TO 1M INCHES
WIDE, ON BRIMS OF SOFT FELT HATS. HAS WORK CLAMP
AUTOMATICALLY OPERATED BY A BELL CRANK RE­
CEIVING ITS MOTION FROM A CAM ON THE UNDER
SIDE OF THE BED. STITCH ADJUSTABLE FROM SEVEN
TO TWENTY TQ THE INCH. REGULARLY FITTED WITH
AN IRON BASE.
NO.
12r>00l
PLATE
Arm
NAME
125002 — 12,5001 with 43.5c, 448c, 15486 and
2002 8534
1.5408.............................................................
Arm Dowel Pin..................................................
1:18 e 853:i
U
Screw.........................................................
12.5003 8525
U
Shaft..........................................................
15108 8525
U
“ Bushing.............................................. .
4350 8533
U
“ “ Set Screw........................................
llln 8533 li
“ Screw.................................................
15100 852.5 U Side Cover................................................
280i) 8534 “ “ Thumb Screw..................................
124 03 8520
U
Spool Pin and Thread Eyelet.................
8870 8530
«
“ “ Washer (cloth)...............................
2138 8520 Balance Wheel (power) light rim, 3 in.
448c 8533
pulley, with two 448c....................................
Balance Wheel Set Screw.................................
*03501 — Bed
03502 8527 Clamp Arm........................................................
03503 8527
U
“ Bracket...........................................
03501 8527
ii
“ Hinge Block with 735c..................
03505 8527
U
“ “ “ Pin.............................................
735c 8533 “ “ “ “ Set Screw..
210n 8.533
U
“ “ “ Screw........................................
20:!n ,853.3
i<
“ Screw..............................................
03500 8.525
u
Carrier with 51815..............................
03507 8527 “ Cap..................................................
21 On 8.533 “ “ Screw...........................................
03.508 8525 “ Lever...............................................
OOOn 8534
n
“ “ Hinge Screw................................