SINGER 101-1 - Manual (Page 3)

INSTRUCTIONS FOR ORDERING
In ordering from this list, use ONLY the part NUMBER
in the FIRST column.
The number stamped on a Sewing Machine part is in every
case the number of the single part only.
Every combination of parts sent out as such has its specific
number, which, although not stamped on the parts, must be
used when ordering the combination.
Each number always indicates the SAME PART in whatever
list it appears, or for whatever machine.
The letters after some of the numbers indicate the style of
finish only, as follows:
A. Hardened, Polished and Plated.
Polished and Plated
Hardened only.
Polished only.
Soft, not Polished.
Hardened and Polished. B.
c.
D.
E.
F.
G.
H.
J.
K.
L.
M.
P.
R.
Blued
Plated only.
Hardened and Plated.
Brass or Gilt.
Oxidized.
Japanned.
Parkerized.
These letters MUST BE USED w h e n they appear in the list,
and AFTER the number as in the list.
In this series
1 to 1500 and 50001 to 51500 are Screw Numbers.
1501 to 1800 are Nut Numbers.
1801 to 2000 are Roller Numbers.
2001 to 60000 and 52001 and upward are numbers of
Machine Parts.
The figures in the second column refer only to the plates,
illustrating the parts, and are NOT TO BE USED in ordering.
Parts marked with an asterisk (*) are furnished only when
repairs B J e made at factory.
LIST OF PARTS COMPLETE
FOR
MACHINE No. 101-1
FOR FAMILY USE. THE ARM AND BED 1$ ONE CASTING, THE BED
IS COVERED WITH A DETACHABLE CLOTH PLATE, THE BOTTOM
MECHANISM IS ENTIRELY ENCLOSED. THE HOOK TRAVELS IN
A HORIZONTAL PLANE OPERATED BY THREE SETS OF GEARS
AT A RATIO OF TWO TO ONE. THE MACHINE IS DRIVEN BY
AN ELECTRIC MOTOR LOCATED IN THE ARM OF THE MACHINE
NEAR THE BALANCE WHEEL ON THE SIDE OPPOSITE THE
OPERATOR.
NO. TLATK NAME EACH
*()()501 — Arm, u[)per and lower (solid) with 66506,
66517 and 6651H............................................. $ —
61)502 s:ioi Arm Lower (lover (back)..................................... 25
66,50;i saoi “ “ “ (front)........................................................ 30
66501 8 :i 02 “ “ Plug (large).................................................. 10
6650.5 h :« i 2 “ “ “ (small)....................................................... 10
66506 8802 “ Oil Tube......................................................... 06
66507 8801 “ Shaft (horizontal)........................................... 3 00
66508 8801 “ “ “ Bushing (back) and
Bobbin Winder Bracket (belt cover). . . 1 80
M5 d 8808 .\mi Shaft (horizontal) Bushing (back)
Screw.......................................................... 06
66.500 8801 .Arm .Shaft (horizontal) Bushing (front) . . 35
•H 6 c 8808 “ “ “ “ “ Set
Screw............................................................... 05
66510 8801 Ann Shaft (horizontal) Bushing (inter-
mediate)........................................................... 1 20
50554c 8808 .Arm .Shaft (horizontal) Bushing (inter-
mediate) Set Screw.......................................... 07
66511 8802 .Ann Shaft (horizontal) Clamp Stop Mo-
tion Collar with two 791c................................ 60
701c 8802 Arm Shaft (horizontal) Clamp Stop Mo-
tion ((ollar Set Screw....................................... 06
t)0()42 8302 Ann Shaft (horizontal) Gear witli two
1259c............................................................... 1 10
66614 8802 Arm Shaft (horizontal) Gear for 190540. . . 3 60
66615 8802 “ “ “ “ Clutch..................................................... 06
66616 8802 “ “ “ “ “ Spring 03
66617 8802 “ “ “ “ Collar with
two 457c.......................................................... 35