Carrier P274-0200-C - Manual

TOTALINi; OWNER’S
MANUAL
Residential
Non-Programmable
Thermostat
Part Numbers P274-0100-C, P274-0200-C, P274-0300-C
IMPORTANT: Read entire instiuctions before program­
ming the tliermostat.
GENERAL
Totaline® thermostats are wall-mounted, low-voltage tlier-
mostats which maint;rin room temperature by controlling the
operation of an HVAC (heating, ventilation and air condition­
ing) system, Sepru'ate heating and cooling set points and
auto-changeover capability allow occupied and unoccupied
programming for energy savings.
During power internjption tlie internal memoiy stores tem­
perature and mode settings for an unlimited time. Batteries are
not required.
OPERATION
Thermostat Display — Tlie thermostat display is locat­
ed in the top center of the thermostat. See Fig. 1. Tlie following
information can be displayed on the screen:
mode (OFF, FIEAT, COOL, EFIEAT, or AUTO)
fan setting (ON or AUTO)
auxiliary heat status (P274-0200-C, -0.Ì00-C only)
room temperature
desired temperature
reset filter
outdoor temperature (P274-0200-C, -0.700-C only)
Thermostat Buttons — The thermostat has buttons
which are used to change the set points of the thennostat and
set the thermostat modes. The buttons are accessible from
behind the thermostat cover. To access the buttons, pull on the
hinged tliermostat cover. The buttons ai'e: MODE, FAN. and
RESET FILTER. See Fig. 1,
Tlie UP and DOWN buttons are used to change tlie cuirent,
desired temperature set point and to scroll through program­
ming set points. The UP and DOWN buttons are located on the
front of the thermostat.
Setting Indoor Temperature Set Points
1. Press the UP or DOWN button one time. The LCD
(liquid crystal display) will illuminate and the current
temperature set point will be displayed. Next to the
temperature display, FIEAT or COOL will be dis­
played. SET TEMP will appear above the temperature
display.
2. To change the temperature set point, continue to press
the UP or DOWN buttons until desired temperature is
reached. Press the MODE button to set temperature for
another setting (Ffeat or Cool).
.7. The thermostat will automatically return to regular
operation within 5 seconds.
NOTE: The cool setting must be at least 2 degrees higher than
tlie heat setting for proper operation.
Fan Operation — Tlie fan button selects fan operation.
Tlie fan can operate in either Fan ON or AUTO mode.
Press the FAN button to switch between fan ON or AUTO
mode. When the fan is set to ON, “FAN” is displayed in the
LCD on the thermostat. The fan will nm continuously for im­
proved air circulation while in the ON position.
When the fan is set to AUTO mode, the fan nms only as
needed to maintain indoor £iir temperature.
NOTE: The “FAN” indicator will not be displayed in the LCD
when thermostat is operating in AUTO mode.
Mode Operation — The Mode button selects the operat­
ing mode of the tliermostat. Pressing tlie MODE button will
rotate the following options on the LCD: OFF, FfEAT, COOL,
AUTO, and EFFEAT (heat pump models only). The mode
for each selection will be displayed on the tliermostat when
selected.
NOTE: If AUTO is selected, the thennostat will enter Pleating
or Cooling mode based on the room temperature and the heat­
ing and cooling set points.
Display Outdoor Temperature — To display the
outdoor-£tir temperature on thermostats offering this feature,
simultaneously press the UP and DOWN buttons for twenty
seconds. Tlie outdoor temperature will then be displayed on the
LCD.
NOTE: Two dashes ” appearing on tlie LCD indicates that
tlie thermostat either does not have this feature installed or the
temperature sensor is not properly connected.
Reset Filter Display — Tlie thermostat win display
“FILTER” on the LCE) when it is time to change or clean the
filter
After cleaning or changing the filter, press the RESET
FILTER button to restart the timer and turn off the indicator.
Auto Changeover Operation — The themiostat win
provide automatic changeover from Heating to Cooling mode
and Cooling to Heating mode when required. The tliermostat
will automatically switch to maintain the desired temperature
setting. The thermostat does not need to be manually changed
from heating to cooling or cooling to heating operation.
Manufacturer reserves the right to
discontinue, or change at any time,
specifications or designs without notice
and without incurring obligations.
REPLACEMENT COMPONENTS DIVISION
©CARRIER CORPORATION 2004 9-04
PRINTED IN U.S.A.
LITERATURE NUMBER P274-7SO
REPLACES: 997-510011-19
CATALOG NO. 570-352