StarTech.com ET91000SC2 - Manual (Page 2)

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access
our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned
for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,
consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow
the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Specifications
ET91000LC2 ET91000SC2
Supported
Standards
IEEE 802.3ab, IEEE 802.3z
Connectors
1 x RJ45 Ethernet
female
2 x LC Fiber female
1 x DC Power
1 x RJ45 Ethernet
female
2 x SC Fiber female
1 x DC Power
Compatible Fiber
Type
Multi Mode
Optical Wavelength 850 nm
Maximum Distance 550 m (1804 ft)
Duplex Modes Full/Half
Auto MDIX Yes (Ethernet)
Power Adapter
12V DC, 1000mA, center positive,
type M plug
Power Consumption < 4W
Enclosure Material Metal
Operating
Temperature
0°C ~ 60°C (32°F ~ 140°F)
Storage
Temperature
-10°C ~ 70°C (14°F ~ 158°F)
Humidity 10% ~ 90% RH
Dimensions (LxWxH) 160.0mm x 95.0mm x 20.0mm
Weight 600g
LED Status
LED Name Status Description
PWR Power
ON Unit is powered
OFF Unit is not powered
RPF
Remote
Power Failure
ON Remote Power Fail
OFF Remote Power Normal
LNK Fiber Link
ON Fiber link is detected
OFF Fiber link is not detected
Blink Fiber activity
LFP
Link Fault
Pass-through
ON LFP Mode enabled
OFF LFP Mode disabled
DIP Switch Settings
Full/ Half:
Ethernet Duplex mode will be configured for Full or Half.
LFP:
Link Fault Pass-through will pass a link failure to the Ethernet
side, if a link failure is encountered on the fiber side and vice
versa. Otherwise, the Ethernet side will continue to show no
link failures, even if the fiber side has no link.
(OFF = Not active, On = Active)
Auto/Force:
Auto negotiate duplex mode, or force Full/Half via DIP
switches.