phil&teds espresso buggy - Manual (Page 2)

Unpacking your Buggy
On arrival and setting up for the first time •
Y
our buggy (frame and fabric items) will arrive in a box. Check the
box is not damaged.
•
The initial setup involves installing: wheels, front wheel J-Bar
,
footplate, fabric items & handle.
Don’t worry - it’
s easy - no tools needed.
Put the wheels on Lie box on floor (T
OP
up). Carefully cut tape and lift of
f top. Check that
all components purchased are in the box. Check no components appear damaged. Carefully lift out wheels (2 rear and one front), and frame. (There may also be accessories purchased in the box.)
Place frame on
floor
, clicking auto-locks (A
& B) in place. Refer diagram above.
Attach the rear wheels by sliding each axle through the axle tubes. Depress the ‘nib spring’ on each axle. Ensure nib pops out once through axle.
These hold the wheels in place. Remove wheels as
required. Attach front wheel:
Pull swivel wheel lock on pipe
out
(refer diagram);
aim J-bar to the side not front; depress nib spring and insert J-bar into pipe; ensure nib spring pops at top and J-bar is flush with plastic bush; push cap over pipe top.
Reverse procedure as required.
Put the handle on Slide the handle onto the frame until nibs “pop”. Ensure the holes in the handle face
down
. Depress the nib springs on undersides
of frame.
1 2 3
Accessories
Call your Most Excellent Dealer for
Accessories and Prices
J Bar
swivel wheel autolock on pipe out
A
B
4
Explorer sleeping bag Un-clip the breastplate.
Thread the safety harness through the 5 slots
in the back of the sleeping bag.
Attach the safety harness to the
breastplate. Fold down the front of the sleeping bag as required. The sleeping bag top can be removed completely and the base used as a buggy liner in warmer weather
.
Remove the liners for separate washing. Follow fabric care label for washing sleeping bag. Colours: Black or Blue T
ravel bag
These bags help protect Kiwi Explorer Buggy
TM
. Remove the rear
wheels and place (axle-to-axle) together
. Place Kiwi Explorer
Buggy
TM
in the travel bag and zip up bag. Carry with the shoulder or
hand straps. Because the fabric has a waterproof layer
, storage of a
damp/wet Kiwi Explorer Buggy
TM
for long periods may result in
fabric mildew
.
Air dry
. Colours: Black
Kiwi mattress Made from the same fabric as the buggy
, the mattress fits the base of
the newborn fitting. Guide the safety harness around the mattress. Use the safety harness in the usual way
.
The mattress can be used in the sitting position for extra back support and comfort. Remove the mattress for cleaning. Fabric care as with buggy fabric. Bacpac Made from the same durable fabric as the buggy
, great for extra
storage and security
.
Attaches to the buggy (upper handle and lower
frame) with quick-release clips. Internal PVC compartment for soiled items. Shoulder straps allow you to carry goods separate from the buggy
.
Removed easily for cleaning. Fabric care as with buggy fabric. Sun-insect mesh and storm cover Mesh protects from insects, wind and sun (SPF 6.5). Storm protects from wind and rain. Fits on handle and snap fastens onto footplate. Child Lifter Sits in newborn position of buggy
. Has a firm base and attaches
using snap fasteners.
Attach 5-point safety harness around child
lifter
.
Sleeping baby can be lifted from the buggy using two handles.
Also
comes with a shoulder strap for easier carrying. Made from the same durable fabric as the buggy and comes in matching colours.
Put the footplate on Position footplate over front of buggy frame. Insert 4 plastic rivets through holes in footplate; match to holes in frame. Rivet must rest on footplate. DO NOT push stalk until rivet rests on footplate. Push (or tap) rivet centre stalk, until flush. Put footplate cover on. Snap fasten footplate cover to frame with logo facing correctly up.