Campbell Hausfeld PW1550 - Manual (Page 4)

Lista de Repuestos
No. de Número del
Ref. Descripción Repuesto Ctd.
Para Ordenar Repuestos o Asistencia Técnica,
sírvase llamer al 1-800-330-0712
(En los Estados Unidos, o llame a su distribuidor local)
1 Adaptador de pivote PM350100SV 1
2 Filtro PM350101SV 1
3 Interruptor N/A 1
4 Manguera PM350110SV 1
5 Pistola PM350109SV 1
6 Lanza de rociado en abanico ajustable PM350104AV 1
7 Soporte para la manguera y cable eléctrico N/A 1
8 Limpiador de puntas PM008500AV 1
9 Salida N/A 1
10 Soporte de la pistola PM350115SV 1
11 Entrada N/A 1
12 Mango N/A 1
13 Anillo en O PM232200SV 1
33 Sp
Instrucciones de montaje y lista de piezas PW1550
Do not spray
electrical apparatus and wiring.
• Never disconnect the high pressure
discharge hose from the machine while
the system is pressurized. To
depressurize machine, turn power and
water supply off, then press gun trigger
2-3 times.
• Never permanently engage the trigger
mechanism on the gun.
• Never operate the machine without all
components properly connected to the
machine (handle, gun/wand assembly,
nozzle, etc.).
Equipment damage.
• ALWAYS turn water supply “ON” before
turning pressure washer “ON.” Running
pump dry causes serious damage.
• Do not operate the pressure washer
with the inlet water screen removed.
Keep screen clear of debris and
sediment.
• NEVER operate pressure washer with
broken or missing parts. Check
equipment regularly and repair or
replace worn or damaged parts
immediately.
• Use only the nozzle supplied with this
machine.
• Never leave the wand unattended while
the machine is running.
• Never attempt to alter factory settings.
Altering factory settings could damage
the unit and will void the warranty.
• Always hold gun and wand firmly when
starting and operating the machine.
• NEVER allow the unit to run with the
trigger released (off) for more than one
(1) minute. Resulting heat buildup will
damage pump.
4
Operating Instructions and Parts List PW1550
In a double-insulated product, two sys-
tems of insulation are provided instead of
grounding. No grounding means are pro-
vided for a double-insulated product, nor
should grounding means be added to the
product. Servicing a double-insulated
product requires extreme care and knowl-
edge of the system, and should be done
only by qualified service personnel.
Replacement parts for a double-insulated
product must be identical to the original
parts. A double-insulated product is
marked with the words “Double
Insulation” or “Double Insulated.”
Product may also be marked with symbol
shown below.
Do not use pressure
that exceeds the operating pressure of
any of the parts (hoses, fittings, etc.) in
the pressurized system. Ensure all
equipment and accessories are rated to
withstand the maximum working
pressure of the unit.
Explosion hazard.
• NEVER spray flammable liquids or use
pressure washer in areas containing
combustible dust, liquids or vapors.
• Never operate this machine in a closed
building or in or near an explosive
environment
Servicing of a Double-
Insulated Appliance
Double Insulated symbol
Sírvase proporcionar la siguiente información:
- Número de modelo
- Número de serie (si lo hubiera)
- Descripción y número del repuesto,
según se indica en la lista de repuestos.
www.chpower.com
2
1
3
4
5
6
7
8
11
10
13
12
9
Dirija toda la correspondencia a:
Campbell Hausfeld
Attn: Customer Service
100 Mundy Memorial Drive
Mt. Juliet, TN 37122 U.S.A
.