Milwaukee Tool 2602-22DC User Manual

Page 2

FUNCTIONAL DESCRIPTION

SYMBOLOGY

ASSEMBLY

WARNING

Recharge only with the

charger specified for the battery. For spe-
cifi c charging instructions, read the operator’s
manual supplied with your charger and battery.

Inserting/Removing the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body of
the tool. Make sure it latches securely into place.

SPECIFICATIONS

Installing the Side Handle
1. To install the side handle,

loosen the side handle grip
until the hooks are far enough
apart to fi t into the slots on
the gear case ring. Posi-
tion the side handle on the
top of the tool, pointing left
or right. Tighten the side
handle grip until it is secure.

2. To remove the side handle,

loosen the side handle grip
until the side handle can be
removed. Reposition and tighten securely.

WARNING

To reduce the risk of injury,

always use a side handle when using this tool.
Always brace or hold securely. Ensure side
handle is tightened securely before each use.

Volts

Direct Current

No Load Revolutions per
Minute (RPM)

Underwriters Laboratories, Inc.
United States and Canada

Cat. No.

Volts

No Load

RPM

No Load

Blows

per Minute

Capacities

Steel

Wood

Masonry

Flat Bit Auger Bit Hole Saw Screws (dia.)

2602-20

Low 0-550

High 0-1700

Low 0-9350

High 0-29,000

1/2”

1-1/2"

2-1/8"

1/4"

5/8"

1. Trigger
2. Control switch
3. LED
4. Keyless chuck
5. Torque selector collar
6. Application selector collar
7. Speed selector

Hooks

Slots

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmos-

pheres, such as in the presence of fl ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause
you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodifi ed plugs and matching outlets will
reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase
the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply. Use of an GFCI
reduces the risk of electric shock.

attached to a rotating part of the power tool may
result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control
of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.

WARNING

READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.

Failure

to follow the warnings and instructions may result in electric shock, fi re and/or serious
injury.

Save all warnings and instructions for future reference.

The term "power

tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool.
Do not use a power tool while you are tired or
under the infl uence of drugs, alcohol or medi-
cation. A moment of inattention while operating
power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your fi nger on the switch or energising power tools
that have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

SERVICE

• Have your power tool serviced by a qualifi ed

repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

SPECIFIC SAFETY RULES

BATTERY TOOL USE AND CARE

• Recharge only with the charger specifi ed by

the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fi re
when used with another battery pack.

• Use power tools only with specifi cally desig-

nated battery packs. Use of any other battery
packs may create a risk of injury and fi re.

• When battery pack is not in use, keep it away

from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery terminals
together may cause burns or a fi re.

• Under abusive conditions, liquid may be eject-

ed from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.

where the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and
could give the operator an electric shock.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.

• WARNING Some dust created by power sanding,

sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:

• lead from lead-based paint
• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are spe-
cially designed to fi lter out microscopic particles.

• Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

•

Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.

•

Hold power tool by insulated gripping
surfaces, when performing an operation