Intex Pool Volleyball Set for Rectangular Ultra Frame Pools - Manual (Page 2)

(52PO) ENGLISH POOL VOLLEYBALL SET MANUAL (FOR RECTANGULAR METAL / ULTRA FRAME POOL) SIZE: 4.875” X 7.25” PANTONE 295U 04/19/2013 (52PO) ENGLISH POOL VOLLEYBALL SET MANUAL (FOR RECTANGULAR METAL / ULTRA FRAME POOL) SIZE: 4.875” X 7.25” PANTONE 295U 04/19/2013
52PO
S AVE THESE INSTRUCTIONS
52PO
S AVE THESE INSTRUCTIONS
English English
2. Secure the pole bracket (7) to the
"U-shape" leg with the U-bolt (2) and
two nuts (3). Clockwise tighten the
dovetail screws (5) using your fingers
only. NOTE: Do not over tighten or
use tool such as pliers.
3. Insert the assembled volleyball pole
into the pole bracket (7). Secure the
pole to the bracket with a long
Pin (1). Clockwise screw in the two
control screws (4) to adjust the pole
vertically position. NOTE: Adjust the
pole inclination by adjusting the
two control screws (4). Do not over
tighten or use tool such as pliers.
4. Attach two volleyball net fasteners
(10) to the volleyball pole. Ensure
the volleyball net fasteners (10) are
facing outward.
5. Locate the opposite "U JOINT" and
attach the second pole bracket (7)
to the "U JOINT", repeat steps #1
to #4.
6. Attach one side of the Volleyball
Net (11) starting from the top
Volleyball Net Fastener (10) and
then the bottom fastener. Loop the
rope around the fastener (10)
several times and secure the end
of the rope to the two notches in
the fastener. NOTE: Adjust the
length of the rope to be looped
around the fasteners depending
on the size of the pool. Repeat
this procedure for the other pole.
Page 4 Page 3
1
3
2
4
7
9
11
10
6
8
5
3
1 2
7
5
2 3
2
3
2
1 4
7 1 4
3
4 8
Vertical Adjustment
10
4
5 10
2
1
6
10
11
REF.
NO.
DESCRIPTION QTY.
RECTANGULAR
METAL FRAME POOL
RECTANGULAR
ULTRA FRAME POOL
SPARE PARTS NO.
1 LONG PIN (WITH 2 EXTRA) 4 10312 10312
2 U-BOLT 2 10544 10901
3 NUT 4 10547 10547
4 CONTROL SCREW 4 10545 10545
5 DOVETAIL SCREW 4 10907 10907
6 RUBBER FENDER 4 10537 10537
7
POLE BRACKET (DOVETAIL SCREWS &
RUBBER FENDERS INCLUDED)
2 10905 10905
8 POLE 2 11173 11173
9 VOLLEYBALL POLE END PLUG 2 10539 10539
10 VOLLEYBALL NET FASTENER 4 10535 10535
11 VOLLEYBALL NET (FOR 9' X 18' & 12' X 24' AGP) OR 1 10866 10866
VOLLEYBALL NET (FOR 16' X 32' AGP) 1 10867 10867
12 VOLLEYBALL 1 10541 10541
4
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
POOL VOLLEYBALL SET UP
IMPORTANT: Before proceeding to the next step ensure the pool is fully set
up and filled with water following the pool owner's manual.
1. Fully open the two dovetail screws (5)
and attach a pole bracket (7) and a
U-bolt (2) to a rectangular metal
frame pool center "U-shape" leg along
the length of the pool. Make sure the
pole bracket (7) is securely attached
to the "U-shape" leg. 4
1
3
2 5
2
7 1
Pool
“U-shape”
leg
POOL VOLLEYBALL SET UP (continued)