Clarion DXZ756MC - Manual (Page 13)

DXZ756MC
13
English
12
DXZ756MC
English
Note:
• When “ADF 1”, “ADF 2”, “ADF 3” or “ADF USER”
is selected for ADF (Anti Distortion Filter), setting
of MAGNA BASS EX cannot be performed.
Setting the Anti Distortion Filter
The adopted “Liveliness Enhancement Filter” and
“Sound Tone Compensation” functions allow well-
modulated realistic playback without affecting the
characteristics of the original sound tone.
This unit is provided with 4 types of sound tone ef-
fects stored in memory. Select the one you prefer.
∗ The factory default setting is “ADF OFF”.
Each time you press the [ADF] button, the tone
effect changes in the following order:
“ADF 1” ➜ “ADF 2” ➜ “ADF 3” ➜ “ADF
USER” ➜ “ADF OFF” ➜ “ADF 1” ...
• ADF 1 : suitable for the genuine speakers
• ADF 2 : suitable for separate speakers
• ADF 3 : suitable for coaxial speakers
• ADF USER: this setting can be adjusted by
the user to his or her individual
preference.
• ADF OFF : no sound effect
Notes:
• The volume changes each time the ADF (Anti Dis-
tortion Filter) setting is switched. Turn down the
volume and the sub-woofer volume before per-
forming a switching operation.
• Sufficient effects cannot be obtained with some
speaker systems. In such cases, adjust the volume.
Adjusting the tone
Press the [A-M] button and select the item to
adjust. Each time you press the [A-M] button,
the item changes as following order:
●When “ADF 1, 2, 3” is set
“SUB-WOOF VOL” ➜ “BALANCE” ➜
“FADER” ➜ Last function mode...
●When “ADF USER” is set
“SUB-WOOF VOL” ➜ “ADF GAIN” ➜
“BALANCE” ➜ “FADER” ➜
Last function mode...
●When “ADF OFF” is set
“SUB-WOOF VOL” ➜ “BASS GAIN” ➜
“TREBLE GAIN” ➜ "BALANCE” ➜
“FADER” ➜ Last function mode...
Notes:
• As subwoofer is effective, “SUB-WOOF VOL” can
be selected.
• The display automatically returns to the previous
mode.
Basic Operations
Adjusting the subwoofer
∗ The factory default setting is “0”
∗ This function can be adjusted only when the
subwoofer output is set to “ON”. For details on how
to set the subwoofer, refer to the subsection “Set-
ting the subwoofer” in the section “Common Op-
erations”.
1. Press the [A-M] button to select “SUB-
WOOF VOL”.
2. Turn the [ROTARY] knob to select from –6 to
+6.
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the ADF effects (Gain, Filter)
This adjustment can only be performed when the
ADF (Anti Distortion Filter) is set to “ADF USER”.
1. Press the [A-M] button and select “ADF GAIN”.
2. Turn the [ROTARY] knob to adjust the gain.
∗ The factory default setting is "1". (Adjustment
range: 1 to 4)
∗ “ADF GAIN” adjusts the filter effect.
3. Move the [ a]/[d] lever to select “ADF FIL-
TER”.
Turn the [ROTARY] knob to select the filter.
∗ The factory default setting is “MID”. (Adjust-
ment LOW/MID/HIGH)
• LOW : attenuates high frequencies.
• MID : attenuates low and high frequen-
cies evenly.
• HIGH : attenuates low frequencies.
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the bass (Gain,
Frequency, Q-curve)
This adjustment can only be performed when the
ADF (Anti Distortion Filter) is set to “ADF OFF”.
1. Press the [A-M] button and select “BASS
GAIN”.
2. Turn the [ROTARY] knob to adjust the bass.
∗ The factory default setting is “0”. (Adjustment
range: –6 to +8)
3. Move the [ a]/[d] lever to select “BASS
FREQ”.
Turn the [ROTARY] knob to select the frequency.
∗ The factory default setting is “50”. (Adjustment
50/80/120 Hz)
7. OPERATIONS
Basic Operations
Note:Be sure to read this chapter referring to the front diagrams of
chapter “3. CONTROLS” on page 5 (unfold).
CAUTION
Be sure to lower the volume before switch-
ing off the unit power or the ignition key. The
unit remembers its last volume setting. If
you switch the power off with the volume up,
when you switch the power back on, the
sudden loud volume may hurt your hearing
and damage the unit.
Turning on/off the power
Note:
• Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Press the [SRC] button.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3. Press and hold the [SRC] button for 1 second
or longer to turn off the power for the unit.
Note:
• System check
During the initial power up of this unit, it will go
through a system check procedure. This proce-
dure verifies any devices connected through
CeNET. Any additional CeNET devices plugged
into the unit after the initial power up will initiate
the system check procedure. When the power is
turned on, “SYSTEM CHECK” appears in the
display if the wire connections were modified. The
system check starts automatically within the unit.
Selecting a mode
1. Press the [SRC] button to change the opera-
tion mode.
2. Each time you press the [SRC] button, the op-
eration mode changes in the following order:
Radio mode ➜ CD/MP3/WMA mode ➜
M.CATCHER mode ➜ CD changer mode
➜ DVD changer mode ➜ TV mode ➜ AUX
mode
➜ Radio mode...
∗ External equipment not connected through
CeNET will not be displayed.
Adjusting the volume
1. Press the front part of the [ROTARY] knob.
The knob will pop up.
2. Turn the [ROTARY] knob to adjust the vol-
ume.
∗ The volume level is from 0 (minimum) to 33
(maximum).
Switching the display
●When the power is turned on
1. Each time you press the [DISP] button, the
display switches in the following order:
Main display ➜ Sub display ➜ Title dis-
play ➜ Main display ...
∗ Once selected, the preferred display becomes
the display default. When a function adjust-
ment such as volume is made, the screen will
momentarily switch to that function’s display,
then revert back to the preferred display sev-
eral seconds after the adjustment.
∗ When you have entered a title in a CD/MP3/
WMA, it appears in the display. If you have not
entered a title, “NO TITLE” appears in the dis-
play. For information on how to enter a title,
refer to the subsection “Entering titles” in the
section “Common Operations”.
●When the power is turned off
1. Each time you press the [DISP] button, the
display switches in the following order:
Clock display ➜ Display off ➜ Clock dis-
play...
Setting MAGNA BASS EXTEND
The MAGNA BASS EXTEND does not adjust
the low frequencies like the normal sound ad-
justment function, but emphasizes the deep
bass frequencies to provide you with a dynamic
sound.
∗ The factory default setting is “OFF”.
1. Press and hold the [A-M] button for 1 second
or longer to turn on the MAGNA BASS EX-
TEND effect. “M-BASS EX ON” appears on
the display.
2. Press and hold the [A-M] button for 1 second
or longer to turn off the MAGNA BASS
EXTEND effect. “M-BASS EX OFF” appears
on the display.