Desa Tech CGEFP33PR - Manual (Page 13)

13 107570
OWNER’S MANUAL
For more information, visit www.desatech.com
Va ria ble Fa n S wi tch W hit e
W hit e
Bla ck
Gr ee n
On
11 0/1 15 V. A. C.
Blo we r Mo to r
Bla ck Bla ck Bla ck Of f
13. Check to make sure that the power cord
and all wires are completely clear of
the blower wheel and that there are no
other foreign objects in blower wheel.
Figure 22 - Installing Bushings (Left Side
Exit shown)
Bushing Location
for Recessed
Installation
Bushing Location
for Freestanding
Installation
Plastic
Bushing
WARNING: Never touch the
blower wheel while in operation.
WARNING: Failure to position
the parts in accordance with sup-
plied diagrams or failure to use
only parts specifically approved
with this heater may result in dam-
age or personal injury.
14. Peel off backing paper and stick sup-
plied wiring diagram decal near center
of firebox bottom (see Figure 23).
Figure 21 - Installing Plastic Bushing for
Power Cord (Right Side Exit Shown)
Right Floor
Support
Bracket
Plastic
Bushing
Continued
Figure 23 - Location of Wiring Diagram Decal 3" from Blower
Wiring
Diagram
120 Vac. 60 Hz. .90 Amps
DESA International, Bowling Green, KY
Red
Variable
Fan Switch Fan Switch
(N.O.)
Green
White
On
110/115
V.A.C.
Blower
Motor
Black
Off 1
2 Black
Blue
WARNING: Never attempt to service heater while it
is plugged in, operating, or hot. Burns and electrical
shock could result. Only a qualified service person
should service or repair heater.
If any of the original wire as supplied with the appliance must be
replaced, it must be replaced with 105
°
C wire or it’s equivalent.
WARNING: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause im-
proper and dangerous operation. Verify proper opera-
tion after servicing.
INSTALLATION
Continued
WARNING: A qualified ser-
vice person must connect fire-
place to gas supply. Follow all
local codes.
If any of the original wire as supplied with
the appliance must be replaced, it must be
replaced with 105˚C wire or it's equivalent.
Operating the Blower
After final installation of your fireplace,
light your gas appliance with the blower off.
After about 15 minutes, turn the blower on
to deliver heated air at the top louvers. The
blower features a variable control which
allows you to select the speed you desire. In
the OFF position, the blower will not oper-
ate. In the ON position, the blower will start
when the thermostat senses a sufficient in-
crease in firebox temperature (approximately
10 to 20 minutes depending on heat setting).
Your gas logs and thermostat blower will
not turn on and off at the same time. The
fireplace may run for several minutes before
the blower turns on. After the heater modu-
lates to the pilot position, the blower will
continue to run. The blower will shut off
after the firebox temperature decreases.
It is safe to operate fireplace with blower
turned off. However, the blower helps dis-
tribute heated air from the fireplace.
Note: Periodically check the louvers of the
firebox and remove any dust, dirt, or other
obstructions.
15. If gas connections have been made and
checked, replace fireplace floor assem-
bly in fireplace. Feed flexible gas sup-
ply line into fireplace base area while
replacing fireplace floor assembly. Make
sure the entire flexible gas line is in fire-
place base area.
IMPORTANT: Do not
pick up fireplace floor assembly by
burners. This could damage burners.
Only handle base by grates.
Note: Be
careful of all wires and components on
underside of floor assembly.
16. Reattach fireplace floor assembly with
screws removed in step 3 of Removing
Fireplace Screen and Floor Assembly,
page 8.
Note: Discard the remaining
hardware items. After assembly, make
sure all wires are completely clear of
blower wheel.
17. Install logs (see Installing Logs, pages
19 and 20) and fireplace screen (see In-
stalling Fireplace Screen, page 20).