IC Realtime 650TVL (Day) 700 TVL(Night) Long Range High Powered (EL-3000) - Manual (Page 6)

10 11
7. Tips for quick installation
OSD KEY
EXTRA VIDEO
OUTPUT
RS485+ RS485-
7-1. Quick control to Zoom & Focus 8-1. On Screen Menu (OSD) menu.
8-2. Setting up the menu
7-2. RS485 Connection
7-3. Quick setting of Smart Zoom
- Push up or down the Tact SW (OSD Key)
by finger for a second without pressing
the switch.
· Up ( ) - Zoom in
· Down ( ) - Zoom out
· Left / Right ( , ) - Focus in/out
RS485 +
RS485 -
or
Keypad controller DVR
You can access to the OSD menu via the remote controller or the DVR as in the
drawing.
8. Functions and operation
FOCUS MODE DISTANCE
EXPOSURE MODE AGC SHUT
SPEED
BLUE
GAIN
LENS
REFRESH
IRIS DSS
HOME
POSITION E.ZOOM
WHITE
BALANCE MODE RED
GAIN
DNR HR MIRROR
OBJECT
DET
SHARP
NESS
INTELLIGENCE
IMAGE
PRIVACY MOTION
DET
SPECIAL
FUNC SCENE
MODE COMM
EFFECT
DISPLAY INIT
SEL DISP SEL SET
TITLE SET INIT
MSG LANGUAGE
MAIN MENU
FLICKER
LESS BRIGHT
NESS WDR/
BLC DAY &
NIGHT
FREEZE
SETUP
STATUS
· Press the Tact SW to enter
· When the adjustment is completed, move the indicator to “SAVE” in the menu and
press the button to save your settings.
· And then move the indicator to “EXIT” to exit the menu (or sub-menu) setting.
· If you select “DFLT (default)” in the menu, the settings in the menu will be restored
to the factory default.
UP
DOWN
RIGHT
Tact SW (OSD button)
LEFT
How to use OSD button (Tact SW)
· Press
-to enter the menu
-to save settings
· Push up or down
-to select functions
· Push left or right
-to adjust a level or mode of sub-menu
[MENU]
[EXIT] [SAVE] [DFLT]
FOCUS
EXPOSURE
WHITE BALANCE
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
ත Note
· If ‘
‘ indica Ɵon appears on a selected sub-menu, press the Tact SW to get into a following menu.
· If ‘ ‘indica Ɵon appears on any sub-menu, it means the funĐƟon with this mark is deacƟvated.
You can set the smart-zooming in the intelligence menu by using the motion detection
and object detection.
** Smart Zoom with Object Detection (OD)
1. Go into the “INTELLIGENCE” mode and select “OBJECT DET” mode.
2. Enable the MODE to “ON” and select “OD area numbers (1 ~ 9)”.
3. Adjust Sensitivity of OD (1 ~ 5)
4. Select Zoom position to move at “ZOOM PRESET”.
Note
dŚĞĐĂŵĞƌĂŝƐĮdžĞĚĂŶĚnjŽŽŵƉŽƐŝƟŽŶŝƐĐĞŶƚĞƌͲnjŽŽŵĞĚ͘
&ŽƌƐŵĂƌƚnjŽŽŵŝŶŐ͕ƚŚĞƉŽƐŝƟŽŶƐŽĨDĂŶĚKĂƌĞƌĞĐŽŵŵĞŶĚĞĚƚŽďĞŽŶƚŚĞĐĞŶƚĞƌ͘
Refer to the INTELLIENCE menu for details (PAGE. 16)
** Smart Zoom with Motion Detection (MD)
1. Go into the “INTELLIGENCE” mode and select “MOTION DET” mode.
2. Enable the MODE to “ON” and select “MD area numbers (1 ~ 3)”.
3. Activate to “ON” and adjust Sensitivity of MD (1 ~ 20)
4. Select Zoom position to move at “ZOOM PRESET”.
ත
. . .
୔G~Œ•G›ŒG{ˆŠ›Gz~GšG—™ŒššŒ‹SG
the MAIN MENU appears on
the screen.
ත Note
For a RS-485 controller, refer to the
page 12 (8-2. Setting up the menu)