Forward or reverse search during play, Repeating play, Setting up a continuous play loop – Philips CD 960 User Manual
Page 6
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
If the current track has no earlier index number:
’ERROR’ appears briefly on the display.
Play starts again from the first index number of the current track.
You can jump back two or more index numbers by pressing
<1 INDEX three or more times quickly in succession.
If you want to jump back to an index number in an earlier track,
you must first select the required track number using PREV
button © and then the required index number using INDEX >
button @.
Forward or reverse search during play
1. Press SEARCH !» button ® for a forward search.
2. Press Keep the button pressed until you reach the required piece of There are three successive search speeds. If you keep the button pressed, the speed increases automatically. If you release the The first speed -This is the slowest speed. SEARCH » again. The second speed -This speed is somewhat higher. The third speed -This is the highest speed. If you try searching past either end of the disc: ’ERROR’ appears briefly on the display. If you reach the end of the disc and release SEARCH W>, play jumps back a few seconds. Repeating play 1. Press REPEAT button @. -’REPEAT’ appears on the display. -The whole disc is repeated over and over. 2. To stop repeat, press REPEAT button (§) again. - ’REPEAT’ goes out. Setting up a continuous play loop 1. During play, press A-B button @ at the required start point. - ’A-B’ flashes on the display. 2. Press A-B button (g) again when the required stopping point is reached. - ’A-B’ lights continuously. - Play immediately jumps back to point A and commences from there until point B is reached. Play then returns to point A and so If you wish to speed up the procedure, you can use SEARCH M> stop times. 3. To break out of the continuous play loop, press CLEAR button - ’A-B’ and ’PROGRAM’ go out. -The continuous play loop is broken, play continues as normal. 5C Possibilities at start of play If you make a mistake, provided that you have not yet pressed start again. Starting with a particular track (Go to track...) 1. Place the disc on the disc-tray. 2. Close the disc-tray. - ’TRACK’ flashes on the display. 4. Press PLAY/REPLAY button ®. - Play starts at the beginning of the selected track. If you select a track which does not exist: ’ERROR’ appears briefly on the display. Starting at a particuiar index number (Go to track.../index...) 1. Enter the required track number. 2. Press SELECT button ®. - ’INDEX’ flashes on the display. 3. Enter the required index number. -The selected index number is shown on the display. 4. Press PLAY/REPLAY button ®. - Play starts at the selected track and index number. If you select an Index number which does not exist: ’ERROR’ appears briefly on the display. Starting at a selected time within a track (Go to track.../ -’MIN’ flashes on the display. 3. Enter the minutes of the desired start time. - ’SEC’ flashes on the display. 5. Enter the seconds of the desired start time. - Play starts at the selected time. If you select a time position which does not exist: ’ERROR’ appears briefly on the display. Scanning a disc 1. Press SCAN button ©. - ’SCAN’ appears on the display. -The first 10 seconds of each track are played in turn. -The track number indicates the track being played. shows the total number of tracks and total playing time of the disc. During the scan, it is possible to use NEXT button ® or PREV 2. During scan, press PLAY/REPLAY button ® the moment you hear a track you wish to play. - ’SCAN’ goes out. point.
music.
button for a moment, the search goes back to the lowest speed.
- It is maintained for a few seconds.
-Sound is audible.
- For location of a passage accurate to within one second.
-This speed is returned to whenever you press
- Also maintained for a few seconds.
- Sound remains audible.
- For fairly accurate location of a passage.
-it is reached after about 10 seconds.
-Sound is no longer audible.
- For a more general location of a passage anywhere on the disc.
- Play stops at the end of the disc.
- ’PROGRAM’ appears on the display.
-The start point of the play loop is set.
-The stop point of the play loop is set.
on.
button ® or NEXT button © to move to the required start and
@.
PLAY/REPLAY, you can press CLEAR button @ at any time and
3. Enter the desired track number using the 0 - 9 digit buttons @.
-The selected track number is shown on the display.
Play starts at the beginning of the selected track.
time...)
1. Enter the required track number.
2. Press SELECT button ® twice.
4. Press SELECT button ® once more.
6. Press PLAY/REPLAY button ®.
Play starts at the beginning of the selected track.
-At the end of the scan, the disc stops and the display again
button @.
-The remainder of the disc is now played, starting at the current