Philips CD 960 - Manual (Page 5)

5. USING THE PLAYER
The following items are desoribed in this section:
A. Playing a complete disc
B. Special features during play
C. Possibilities at start of play
D. Programming
E. FTS (Favourite Track Selection)
F. Other possibilities
- When using this Compact Disc player, various indications in the
display explain what is happening. These are given below.
- If, however, something does not occur as expected, advice is
also given to explain why this may be.
-To help you to locate buttons easily, the names used
throughout the text are the same as those marked on the player.
The numbers in circles refer to the main illustrations inside the
back cover.
5A Playing a complete disc
1. Switch on your amplifier
2. Set the source selector on your amplifier to correspond to the
Compact Disc player input.
3. Press ON/OFF switch (i).
-The display ® lights.
If the display does not light:
Is the mains lead connected properly at both ends?
Is power available at the mains socket?
4. Set PLAY MCDE switch (g) to ’NCRM PLAY’.
5. Press CPEN/CLCSE button ®.
-The disc-tray @ opens.
6. With your hand open, and thumb and fingers extended, take the
disc out of its holder and fit it, label side up, into the cradle in the
disc tray (Fig. 6-7).
7. Close the disc-tray by pressing the CPEN/CLCSE button @.
You can also simply push in the disc-tray to close it.
- 'DISC flashes on the display.
-The disc spins for a moment and then stops.
-The total number of tracks and total playing time of the disc are
shown on the display.
If 'ERROR' appears briefly on the display:
Check that the disc has been inserted correctly.
Is the disc dirty or damaged in anyway? (See Section 6E - Maintenance).
8. Press PLAY/REPLAY button d).
-The disc starts to spin.
-The track and index numbers refer to the track being played,
starting at track 1, index 1.
-The elapsed playing time of each track is shown above 'MIN’
and ’SEC.
- 'LAP' appears on the display.
- Play starts.
You can go directly from step 6 to step 8. In this case,
programming Is not possible.
If no sound (or distorted sound) Is heard:
Is the correct source selected on the amplifier?
Is the volume control on the amplifier set to minimum?
Is the Compact Disc player connected to your amplifier correctly? See
Section 4 - Installation.
Is the player positioned horizontally?
9. Press REM/LAP button ® whenever you want to know the
remaining time of the whole disc.
- 'REM' (Instead of 'LAP') then appears on the display: the time
Indication changes.
- After playing the last track, the player stops automatically. The
total number of tracks and the total playing time of the disc are
again displayed.
10. Press OPEN/CLOSE button @.
-The disc-tray opens.
-The information disappears from the display.
11. Take the disc from the disc-tray.
12. Close the disc-tray.
-'ERROR' and 'DISC' appear briefly on the display, indicating
there is no disc on the disc-tray.
13. Press ON/OFF switch 0.
-The display goes out.
-The player is now switched off.
SB Special features during play
Short interruption of play
1. Press PAUSE button @.
- 'PAUSE' appears on the display.
-The music stops but the disc continues to spin.
2. Press PAUSE button © again to restart play from where it was
interrupted.
, NEXT and PREV may all be used
during pause to move to a particular location. However, play will
not commence until PAUSE button © is pressed again.
Stopping play
Press STOP/CM button ©.
-The disc stops spinning.
-The display again shows the total number of tracks and total
playing time.
Returning to the start of the current track
Press PLAY/REPLAY button ®.
- Play stops for a moment then restarts at the beginning of the
track.
Moving to the next track (or any later track)
Press NEXT button ®.
- Play stops for a moment, then restarts at the beginning of the
next track.
If there is no next track on the disc:
'ERROR' appears briefly on the display.
Play continues with the current track.
You can jump forward two or more tracks by pressing NEXT two
or more times in succession.
Moving back to the previous track (or any earlier track)
Press PREV button ©.
- Play stops for a moment, then restarts at the beginning of the
previous track.
If there is no previous track on the disc:
'ERROR' appears briefly on the display.
Play continues with the current track.
You can jump back two or more tracks by pressing PREV two or
more times in succession.
Moving to the next (or any later) index number
Press INDEX > button ©.
- Play stops for a moment, then restarts at the beginning of the
next index number (of the current track).
If the current track has no further index number:
'ERROR' appears briefly on the display.
Play starts again from the first index number of the current track.
You can jump forward two or more index numbers by pressing
INDEX > two or more times in succession,
if you want to jump fon/vard to an index number in a later track,
you must first select the required track number using NEXT
button 0 and then the required index number using INDEX >
button @.
Returning to the start of the current index number
Press < INDEX button @
- Play stops for a moment, then restarts at the beginning of the
index number.
Moving back to the previous (or any earlier) index number
Press < INDEX button © twice quickly in succession.
- Play stops for a moment, then restarts at the beginning of the
previous index number.