Drawmer MC2.1 Monitor Controller - Manual (Page 3)

3 MC2.1 - Monitor Controller
COPYRIGHT
This manual is copyrighted © 2013 by Drawmer Electronics Ltd. W ith all rights reserved. Under copyright
laws, no part of this publication may be reproduced, transmitted, stored in a retrieval system or translated
into any language in any form by any means, mechanical, optical, electronic, recording, or otherwise,
without the written permission of Drawmer Electronics Ltd.
Drawmer Electronics Ltd., warrants the Drawmer MC2.1 Monitor
Controller to conform substantially to the specifications of this
manual for a period of one year from the original date of purchase
when used in accordance with the specifications detailed in this
manual. In the case of a valid warranty claim, your sole and exclusive
remedy and Drawmer’s entire liability under any theory of liability will
be to, at Drawmer’s discretion, repair or replace the product without
charge, or, if not possible, to refund the purchase price to you. This
warranty is not transferable. It applies only to the original purchaser
of the product.
For warranty service please call your local Drawmer dealer.
Alternatively call Drawmer Electronics Ltd. at +44 (0)1709 527574.
Then ship the defective product, with transportation and insurance
charges pre-paid, to Drawmer Electronics Ltd., Coleman Street,
Parkgate, Rotherham, S62 6EL UK. Write the RA number in large
letters in a prominent position on the shipping box. Enclose your
name, address, telephone number, copy of the original sales invoice
and a detailed description of the problem. Drawmer will not accept
responsibility for loss or damage during transit.
This warranty is void if the product has been damaged by misuse,
modification, unauthorised repair or installed with other equipment
that proved to be faulty.
THIS WARRANTY IS IN LIEU OF ALL W ARRANTIES, WHETHER
ORAL OR WRITTEN, EXPRESSED, IMPLIED OR STATUTORY.
DRAW MER MAKES NO OTHER W ARRANTY EITHER
EXPRESS OR IMPLIED, INCLUDING, W ITHOUT LIMITATION,
ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT.
PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY SHALL BE REPAIR OR REPLACEMENT AS
SPECIFIED HEREIN.
IN NO EVENT W ILL DRAWMER ELECTRONICS LTD. BE LIABLE
FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM ANY
DEFECT IN THE PRODUCT, INCLUDING LOST PROFITS,
DAMAGE TO PROPERTY, AND, TO THE EXTENT PERMITTED
BY LAW , DAMAGE FOR PERSONAL INJURY, EVEN IF
DRAW MER HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Some states and specific countries do not allow the exclusion of
implied warranties or limitations on how long an implied warranty may
last, so the above limitations may not apply to you. This warranty gives
you specific legal rights. You may have additional rights that vary from
state to state, and country to country.
For the USA
FEDERAL COMMUNICATIONS COMMISSION RADIO
FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off an
on, then the user is encouraged to try to correct the interference by
one or more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Unauthorised changes or modification to this system can void the
users’ authority to operate this equipment.
This equipment requires shielded interface cables in order to meet
FCC class B limit.
For Canada
CLASS B NOTICE
This digital apparatus does not exceed the Class B limits for radio
noise emissions set out in the Radio Interference Regulations of the
Canadian Department of Communications.
CLASSE B AVIS
Cet appareil numérique ne dépasse pas les limites de la classe B au
niveau des émissions de bruits radioélectriques fixés dans le
Règlement des signaux parasites par le ministère Canadien des
Communications.
In the interests of product development, Drawmer reserve the right to modify
or improve specifications of this product at any time, without prior notice.
SAFETY CONSIDERATIONS
CAUTION - SERVICING
DO NOT OPEN. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
TO REDUCE RISK OF FIRE/ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO MOISTURE.
WARNING
DO NOT ATTEMPT TO CHANGE OR TAMPER W ITH THE SUPPLIED MAINS CABLES.
WARNING
TO REDUCE THE RISK OF FIRE REPLACE THE MAINS FUSES ONLY W ITH A FUSE THAT
CONFORMS TO IEC127-2. 250 VOLT WORKING, TIME DELAY TYPE AND BODY SIZE OF 20mm x
5mm. THE MAINS INPUT FUSE MUST BE RATED AT T315mA at 115V and T160mA at 315V.
ONE YEAR LIMITED WARRANTY