Channel Plus 5545 - Manual (Page 3)

5500 Series modulators
RF output
Physical dimension: 1.5” (3.8 cm) height x 7.97” (20.2 cm) width x 5.54” (14.1 cm) depth
performance
Video
Inputs
Channel 65-125 (excluding 95-99)
Channel 14 - 64
model number
signal/noise 55 dB
-60 dBC
+25 dBmV (85dBµV)
105-125 VAC
-45dBC @ 12MHz
15 VDC
differential phase <4º
differential gain
L & R inputs combined for monaural
4%
audio 1 V rms @ 47k
video
UHF
350-079 350-082
CATV
1 Vp-p @ 75
output level
input voltage
IM distortion
alternate channel
output voltage
output current 600mA 900mA
DECLARATION OF CONFORMITY
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
FCC classifies this product under part 15 of its rules as a “television interface device”.
Systems designed using television interface devices have the following legal requirements:
1) The modulated channel signal strength may not exceed 15.56dBmV at any television.
2) If an antenna is used in the system, the modulated channel signal strength may not exceed
-51dBmV at the antenna input port.
The system you design must comply with these regulations. As the installer, you are
responsible. The easiest way to be fully compliant is to use a ChannelPlus coax panel.
ChannelPlus panels have the necessary isolation from the modulator input ports to the
antenna input port and gain characteristic from the modulator input ports to the television
output ports. These features will make your modulator comply with the above requirements.
The shown is fully compliant.
Installation requirements:
For the Installer:
Federal Regulation 47CFR15.115(b)(1)(i).
Federal Regulation 47CFR15.115(c)(4).
Typical Installation
Model 5525 5545
Weight: 2 lbs
Power supply
Mounting hole template
To hang with connectors on the side
To hang with connectors on the bottom or top
10
Specifications: typical @ 25 C ± 5 C O O
3
14) Protective Attachment Plug - The product is equipped with an attachment plug having
overload protection. This is a safety feature. See Instruction Manual for replacement
or resetting of protective device. If replacement of the plug is required, be sure the
service technician has used a replacement-plug specified by the manufacturer that
has the same overload protection as the original plug.
15) Outdoors Antenna Grounding - If an outside antenna or cable system is connected to
the product, be sure the antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements for the grounding
electrode. See figure A.
16) Lightning - For added protection for this product during a lightning storm, or when it is
left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the product due
to lightning and power-line surges.
17) Power Lines -An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits as contact with
them might be fatal.
18) Overloading - Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
19) Object and Liquid Entry - Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the product.
20) Servicing - Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
21) Damage Requiring Service - Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an
improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to its
normal operation,
e) If the product has been dropped or damaged in any way, and
f ) When the product exhibits a distinct change in performance - this indicates a need for
service.
22) Replacement Parts - When re placement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the
same characteristics as the original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.