Culligan US-640 - Manual (Page 5)

NOTE: Substances reduced are not necessarily in your water. Filter must be maintained
according to manufacturer’s instructions, including replacement of filter cartridges.
WARNING: Do not use with water that is microbiologically unsafe or of unknown
quality without adequate disinfection before or after the system. Systems certified for cyst
reduction may be used on disinfected waters that may contain filterable cysts.
Contact your area retailer or local water treatment professional for replacement cartridge
pricing.
Suggested Retail Price for Replacement Filter Cartridges: D-40 $39.99
Test Conditions Operating Requirements
Flow Rate = 0.6 gpm Pressure = 30–125 psi (2.1-8.6 bar)
Inlet Pressure= 60 psi (4.1 bar) Temperature = 40–100°F (4.4–37.8°C)
pH = 7.5 ± 1 Turbidity = 5 NTU Max.
Temperature = 68°F ± 5°F (20°C ± 2.5°C)
2
1
3
4
11 10
9
5
8
6
7
12
Replacement Parts
1 144802 Pressure-Relief Assembly
2 154530 White Cap
3 143338 Screws for Mounting Bracket
4 151231 O-ring (OR-233)
5 155466 D-40 Filter Cartridge
6 153126 White Housing
7 150424 Housing Wrench (SW-5)
8 151242 Lead-Free Faucet (FT-10)
9 143209 Quick-Connect Tee
10 143410 Quick-Connect Union
11 144805 Quick-Connect Faucet Adapter
12 144097 Clear 3/8-inch Tubing
For replacement parts, contact your nearest retailer or callCulligan Consumer Services at 1-888-777-7962.
Performance Data
Model US-640
Important Notice: Read this performance data and compare the capabilities of this system
with your actual water treatment needs. It is recommended that, before installing a water
treatment system, you have your water supply tested to determine your actual water treat-
ment needs.
This system has been tested according to NSF/ANSI 42 and 53 for reduction of the sub-
stances listed below. The concentration of the indicated substances in water entering the
system was reduced to a concentration less than or equal to the permissible limit for water
leaving the system, as specified in NSF/ANSI 42 and 53.
D-40 Cartridge
Substance Influent Challenge Max. Permissible Product Reduction Minimum Average
Concentration Water Concentration Requirements Reduction Reduction
Standard 42 Aesthetic Effects
Chlorine
2.0 mg/L ± 10% ≥ 50% 97%
Particulates at least 10,000 particles/mL ≥ 85% 96%
(0.5 to < 1µm) Class I
Standard 53 Health Effects
Cysts
2) Minimum 50,000/L 99.95% 99.99% 99.99%
Turbidity 11 ± 1 NTU 0.5 NTU 99.1% 99.4%
Asbestos 10 7 to 10 8 fibers/L >10 99% 99.9% 99.9%
Micrometers in length
Lead 6.5 pH 0.15 mg/L ± 10% 0.010 mg/L 99.3% 99.3%
Lead 8.5 pH 0.15 mg/L ± 10% 0.010 mg/L 94.1% 97.6%
Mercury 6.5 pH 0.006 mg/L ± 10% 0.002 mg/L 85% 90.8%
Mercury 8.5 pH 0.006 mg/L ± 10% 0.002 mg/L 80.6% 90%
Atrazine 0.009 mg/L ± 10% 0.003 mg/L 89% 89%
Lindane 0.002 mg/L ± 10% 0.0002 mg/L 92.4% 92.4%
Flow Rate = 0.6 gpm (2.27 L/min) Capacity = 600 gallons (2271 L) or 6 months
2) Based on the use of microspheres
Testing was performed under standard laboratory conditions, actual performance may vary.
5