Canceling a cycle, To stop the drain, To clear the indicators – Kenmore ULTRA WASH 665.16837 User Manual
Page 14: Changing a cycle or setting, During the first fiil of a cycle, After the first fill of a cycle
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
(
C
hina
)
W
entl
^
Use this cycle for china
Use
and crystal. This cycle
covered
uses a light wash and
detergent
gentle dry. During the
dispenser
heated dry, the heating
section,
element cycles on and off.
Initial display time: 68 min
Soil
Level
Sensed
Wash
Rinse
Main
Wash
Rinse
or
Purge
Final
Heated
Rinse
Dry
Cycle
Time
(min)
Water
Usage
(gal/L)
Heavy
•
•
•
•
130°F
(54'C)
•
cycled
72*
8.6/32.7
Ught
•
•
•
130'F
(54X)
#
cycled
5S*
4.8/18.2
T
ime
SAVER
Use this cycle for pre-
Use
rinsed or lightly-soiled
covered
loads. The sensor adds
detergent
water and time, if needed,
dispenser
for maximum cleaning.
section.
No drying options are
available for this cycle.
Initial display time: 26 min
Soil
Level
Sensed
Wash
Rinse
Main
Wash
Purge
Final
Heated
Rinse
Dry
Cycle
Time
(min)
Water
Usage
(gal/L)
Heavy
•
•
•
•
140*F
(60X)
30*
6.9/26.1
Light
•
•
•
140"F
(60*0
26*
4.8/18.2
(
Q
uick
^
V RINSE
J
Use
this rinse cycle for
Do not use
rinsing dishes, glasses,
detergent
and silverware that will
with this
not be washed right away,
cycle.
Initial display time: 10 min
Soil
Level
Sensed
Wash Rinse
Main
Wash
Rinse
Final
Heated
Rinse
Dry
Cycle
Time
(min)
Water
Usage
(gal/L)
Heavy
•
•
14
4.3/16>4
Ught
•
10
2.2/8.2
NOTE:
The sensor in your dishwasher monitors the soil level.
Cycle time and/or water usage can vary from the numbers above
as the sensor adjusts the cycle for the best wash performance.
Canceling a Cycle
Anytime during a cycle, press
The dishwasher pauses for about 5 seconds. Then the
display shows
Your dishwasher starts a 2 minute drain (if needed). Let the
dishwasher drain completely. The light turns off after 2
minutes.
NOTE:
If your dishwasher does not need draining, the light turns
off. Select a new cycle and options.
To stop the drain
You can press Cancel/Drain again to stop the drain immediately.
Remember to drain the dishwasher before starting a new cycle.
NOTE:
A small amount of water remains in the dishwasher. This
is normal.
To clear the indicators
Press Cancel/Drain before starting the dishwasher to clear all
options and cycles.
Changing a Cycle or Setting
During the first fiil of a cycle
1. Press a new cycle and/or options.
2. Check the detergent dispensers. They must be filled properly
for the new cycle.
After the first fill of a cycle
1.
Press
The display shows
3.
4.
5.
Your dishwasher starts a 2 minute drain (if needed). Let the
dishwasher drain completely. The light turns off after 2
minutes.
NOTE:
if your dishwasher does not need draining, the light
turns off.
Check the detergent dispensers. They must be filled properly
for the new cycle.
Close the door.
Press a new cycle and/or options.
Press START.
14