Kenmore ULTRASOFT 400 625.3884 - Manual (Page 7)

JJJJJJJJJJJJJJJJJJJJJJJJJ.
JJJJJJJJJJJJJJJJJJJJJJJJJ
JJJJJJJJJJJJJJJJJJJJJJJJJ. SECTION 1 JJJJJJJJJJJJJJJJJJJJJJJJJ.
JJJJJJJJJJJJJJJJJJJJJJJJJ
JJJJJJJJJJJJJJJJJJJJJJJJJ.
WATER SOFTENER START UP
C. PROGRAM THE TIMER
^ SET WATER HARDNESS NUMBER
■ Press the SELECT 1 button once to display 25
(flashing) and HARDNESS.
The grains per gallon (gpg) hard­
ness of your water supply is on
your water analysis report. Be
sure to enter water test results on
page A, for future reference.
¿'S
Df your water supply contains iron, compensate for
it by adding to the water hardness number. For ex­
ample, assume your water is 20 gpg hard and contains 2
ppm iron. Add 5 to the hardness number for each 1 ppm
of iron. In this example, you would use "0for your hard­
ness number.
2 ppm iron X 5
2
10
(times)
20 gpg hardness
+10
30 HARDNESS NUMBER
■ Press the UP / DOWN buttons to set your water
hardness number in the display. The DOWN button
moves the display to 1. The UP button moves the
display to the highest setting (see maximum setting
for your model in the specifications).
Note:
Between 1 and 25, each press of the UP / DOWN
button changes the display by 1. Between 25 and
the highest number, the display changes 5 at a
time^25,30,35, etc. Holding the UP or DOWN but­
ton in changes the display twice each second.
^ SET RECHARGE (REGENERATION) TIME
■ Press the SELECT 1 button to display 2:00 AM
(flashing) and RECHARGE TIME.
At the 2:00 AM recharge time
setting, the softener begins re-
i,nn^
C'ULI
RECHARGE
TIME
generation (see pages 2-4 and 2-5) at 2:00 AM, end­
ing no later than 4:00 AM. This is a good time in
most households because water is not being used
(see Automatic Bypass, page 2-6). If a different re­
charge time setting would be better for your house­
hold, do the following.
■ Press the UP / DOWN buttons to set the desired
recharge starting hour. Be sure to observe the AM-
PM as you did when setting the present time of day.
Note:
Each press of the UP / DOWN buttons changes the
display one hour. Holding the buttons in changes
the display twice each second.
^]| SET SALT TYPE (sodium chloride or potas­
sium chloride, see page 1-6):
■ Press the SELECT 1 button to display nACl, the
default setting.
Df you want to use potassium
chloride
(KCl) instead of stan­
dard sodium chloride (NaCl)
water softener salt, be sure to set
KCl in the display using the UP
button. The KCl setting adjusts
regeneration cycle times to com­
pensate for the variable dissolv­
ing rate of potassium chloride.
SALTSIGNAl
EVEILEVEL
8
7
6
5
4
3
2
1
n R C I
SALTSIGNA
.EVEILEVEL
8
7
6
5
4
3
2
1
K C l
KCl
■ Press the SELECT button once again, to return
the present time, and RECHARGE TONIGHT in the
display.
5d9'
RECHARGE TONIGH7
DF YOU NEED HELP PROGRAMMDNG THE TDMER, CALL TOLL FREE,
NUMBER 1-800-426-9345.
www.KenmoreWater.com
SEE PAGES 2-1, 2-2 AND 2-3 FOR OTHER FACE PLATE TIMER FEATURES.
1
-
4
SALTSIGNAl
.EVEilEVEL
SAUSIGNAL
.EVEILEVEL
SALTSIGNAl
.EVEILEVEL