Kenmore 665.1649 - Manual (Page 15)

During the fiist minute of a cycle
1. Open the door.
2. Press a new cycle and/or options.
3. Check the detergent dispensers. They must be filled properly
for the new cycle.
4. Close the door. The dishwasher resumes the new cycle
and/or option after a 5-second pause.
After the first minute of a cycle
1. Carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door to access the
control panel.
2. Press CANCEL. The Cancel light glows.
3. Close the door. Your dishwasher starts a 2-minute drain (if
needed). Let the dishwasher drain compietety. The tight turns
off after 2 minutes.
NOTE: If your dishwasher does not need draining, the light
turns off.
4. Cpen the door. Select a new cycle and/or options.
5. Check the detergent dispensers. They must be filled properly
for the new cycle.
6. Press START and firmly close the door (on top control
models). Cr, firmly close the door and press START {on split
control models).
You can add an item anytime before the main wash starts. Cpen
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
1. Carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door.
2. Cpen the door, if the detergent dispenser cover is still closed,
add the item.
3. Close the door firmly until it latches. The dishwasher resumes
the cycle after about a 5-second pause.
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off,
or select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
any time before drying begins.
Press START to use the same cycle and option(s) as the previous
wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press Start, the dishwasher runs the last full wash cycle and
options.
Hi Temp Wash
Select this option to increase the water temperature during the
wash portions of the cycle. Hi Temp Wash raises the water
temperature to 145°F (63°C), in the main wash. Heating the water
helps improve washing results. Hi Temp Wash is useful when
loads contain baked-on food.
This option adds heat, wash time and may add water to the
cycle.
NOTE: Hi Temp Wash is an option with the Smart Wash, Anti
Bacterial, and Normal Wash cycles.
Sani Rinse
Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C). Sani Rinse adds heat and time to
the cycle. This high temperature rinse sanitizes your dishes and
glassware in accordance with NSF/ANSI Standard 184 for
Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments.
NOTE: The Anti Bacterial cycle automatically uses this option.
Sani Rinse is an option with SmartWash and Normal Wash. Only
these sanitization cycles have been designed to meet the NSF/
ANSI requirements.
Air Dry
Select this option to dry without heat. Air drying is useful when
loads contain plastic dinnerware that may be sensitive to high
temperatures.
The dishes take longer to dry and some spotting can occur. For
best drying, use a liquid rinse aid. Some items (such as plastics)
may need towel drying.
NOTE: Air Dry is an option with all cycles, except Quick Rinse.
Lock On
Use the Lock On to prevent unintended use of the dishwasher.
You can also use the lock feature to prevent unintended cycle or
option changes during a cycle.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked.
To turn on the Lock
Press and hold AIR DRY for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
To turn off the Lock
Press and hold AIR DRY for 4 seconds. The light turns off.
Delay Hours/4 Hour Delay
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay. After adding items, firmly close the door until it latches.
The delay will not continue if the door is not latched.
To delay the start
1. Press the delay button to choose the number of hours
delayed.
2. Select a wash cycle and options.
3. Press START.
The dishwasher starts the cycle in the selected number of hours.
NOTES:
■ To cancel the delay and cycle, press CANCEL.
■ To cancel the delay and start the cycle, press START.
15