Kenmore 790.7942 - Manual (Page 7)

Before Using Your Range
Assembly of Burner Heads & Burner Caps (for Deep Well Cooktop models only)
Your range is shipped with the Burner Heads and Burner Caps in the correct locations. Packing material is located between
the Burner Heads and the cooktop.
a. Be sure to follow the installation instructions before
installing and using your new range.
b. Remove ail packing tape from cooktop area. Remove all
Burner Caps and Burner Heads.
c. Discard all packing material located under Burner Heads.
d. To replace Burner Heads & Caps, match the letters
located under center of Burner Caps with the letters
located inside Burner Heads (Fig. 1).
e. Match the letters stamped on Burner Skirts with Burner
Heads and Burner Caps (See Fig. 1). Replace the Burner
Heads and Caps on cooktop (See Fig. 2). Carefully align
the Electrodes into slot or hole of each Burner Head (Fig.
3). Note: The Burner Heads should sit flat on Cooktop
Burner Skirts.
f. Unpack Burner Grates and position on the cooktop.
Fig. 1
Fig. 3
align into slot or hole for each
Burner Head
Assembly of Burner Heads & Burner Caps (for Ceramic Glass Cooktop models only)
Your range is shipped with the Burner Heads and Burner Caps in the correct locations. Packing material is located between
the Burner Heads and burner skirts.
a. Be sure to follow the installation instructions before
installing and using your new range.
b. Remove any packing tape from cooktop. Remove all
Burner Caps and Burner Heads, except DO NOT RE­
MOVE Burner Head for Triple Ring Burner (right-front
burner position; See Fig. 4).
c. Discard any packing material located under the Burner
Heads (except Triple Ring Bumerposition).
d. Replace right rear Burner Head & Cap onto cooktop.
Match the letter for the right-rear burner located inside of
Burner Cap with the letter located inside Burner Head
(only the right-rear position is marked with letter A - See
Fig. 5). Carefully align the Electrode into slot of Simmer
Burner Head (Fig. 7).
e. CAREFULLY (DO NOT FORCE) align the Bridge Burner
Head over the 2 Bridge Burner Electrodes located on left
side of the cooktop. After placing the Bridge Burner Head
on the burner skirt, MAKE SURE that the Bridge Burner
Head lies evenly on burnerskirt.
f. Replace Bridge Burner Caps. These include 1 Bridge
Burner Center Cap (rectangular shaped) and the 2 Bridge
Burner End Caps (The Bridge Burner End Caps will fit at
either the front or rear Bridge Burner Head locations).
Make sure that the tabs located under the Bridge Burner
Caps fall into the slots located in the Bridge Burner Head
(See black arrows in Fig. 6) and that the Bridge Burner
Caps lie flat and evenly on top the Bridge Burner Head.
g. Unpack Burner Grates. Position End Burner Grates on
cooktop. Place Center Burner Grate between the end
Burner Grates and check that all the Burner Grate legs lie
fiat on the glass cooktop surface.
i?k
9k
.. 3 positrons' ' 5 k a
" illiiilB''
Burner
Head
Trillile Ring
Burner
.;k -
Fig. 4
Bridge Burner
Head
..i'Ai,'" Burner
Cfiu
Fig. 5
^
1
:
■ -.
- 2 Electrode V Electrode
hole must align into slot or hols
locations
for Simmer Burner Head
through
Bridge
Burner
Head
Fig. 7
Fig. 6