beautypg.com

Cleaning, Service parts, Light bulb replacement – Kenmore GLIDE AWAY 233.5998892 User Manual

Page 2: A/iring diagram

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

Cleaning

WARNING

ALWAYS

DISCONNECT

ELECTRIC

POWER

SUPPLY

BEFORE SERVICING HOOD.

i>UPPLY

SERVICE PARTS

Kenmore Range Hood * Model 233.5998892 Black

Model 233.5998811 White

Use a mild detergent suitable for painted surfaces. DO NOT USE

POwmFpl

SCOURING

POWDERS. Vacuum blower to clean. Do not immerse blower in

W3t©r.

Wash the foam filter in a mild detergent solution.

io!^c?eaning:^'^®' assembly and light lens are easily removable

See Step 13 on page 4 for removal of glass drawer
assembly. DO NOT clean in a dishwasher.

Remove the light lens by opening the filter panel
(Step 6, page 2) and rotating the 2 metal clips

holding the lens in place.

Light Bulb Replacement

Your hood uses a 24" long F20T12 fluorescent tube and an FS’2
starter, which are available at most hardware stores or home
centers.

To check or replace tube: 1) Pull drawer out. 2) Rotate filterpanel

clips and lower filter panel.

If the tube flickers or does not light, check the prongs on the ends
cf the tube to make sure they are properly seated in the tube
nolders.

^ the tube continues to flicker or does not tight, replace the tube.
Slide the tube into the holders and rotate the tube so that the
xongs in the holders grip the tube and hold it in place.

f the ends of the tube light but the center does not, the starter

nay require replacement. The starter is located behind the filter

janel on the right hand side. Install the new starter by pushing

he starter in and turning it clockwise.

f the tube still does not light, order a 99270651 Ballast Trans-

ormer available through Sears stores.

A/IRING DIAGRAM

KEY
NO.

1

2

3
4
5
6

7

8

9

10

11

12
13
14

15

16
17
18

19

20
21
22
23

24
25
26
27

28

29
30

31
32
33
34

35
36
37
38
39

40
41
42
43
44

46
48
49

50

BLACK

PART NO.

98006940
99150526
9Э090677

99360133
99170245
97006078

98005221

99100379
97008644
97008641
93260454

97011874

97008578
97008618

99160344
99150538
99150537
97008594

99230345
99160319
98005860
99270550
99270651

99270553
97008619

99400042
98006937

98006938
99100463
97008971

97008970

99250932
97009057
99110683
99420508

98007155
99020139
98005212
99100491
99080359

99260476
99420464
97007314
99020138
99140156

99010175
97011138
99050018
99150492
99100408
99150471

97008626
97005965

99041399

WHITE

PART NO.

96007168
99150478

99090697
99360140
99170245
97006078

98005221

99100379
97008981
97008982

93260454

¡97011873

97008578
97008618

99160344
99150638
99150537
97008594

99230342
99160319
98005860
99270550
99270651
99270553

97008619
99400042
98007164
98006938
99100463

97008979

97008978

99250932

97009117
99110699
99420514
98007155
99020139

98005212
99100491
99080359
99260476
99420464
97007314

99020138
99140156
99010175
97011139
99050018
99150492

99100464
99150471
97008628
97005985

DESCRIPTION

99041399

Front Trim

Screw #8-18 X 3/8 (14 Required)'
Conirof Trim

Control Knob

Screw #8-18 X 3/8 (8 Required)'
Damper Assembly (Includes Key Nos

7 & 8)

Damper Flap

'

Damper Boshing

RH Mounting Bracket (Includes Key No. 10)
LH Mounting Bracket (Includes Key No. 10)

#8 Sheet Metal Nut “U" Type

(11 Required)

Canopy
Control Board

Control Harness
Screw #8-32 X 3/16 (5 Required)'
Screw #8-18 X 2 (4 Required)'
Screw #8-18 X 1 (4 Required)'
Switch Assembly

Rivet (13 Required)

Screw #6-32 X 3/8 (4 Required)'
Lampholder Bracket (2 Required)

Lampholder (2 Required)
Ballast Transformer

Starter FS-2'
Light Harness

Strain Relief Bushing SR-4N-4 (2 Required)
Access Cover
Wire Box Cover
Drawer Stop (2 Required)

LH Drawer Bracket Assembly (Includes Key

Nos. 32 & 33)

RH Drawer Bracket Assembly (includes

Key Nos. 32 & 33)

Washer (2 Required)*

Drawer Assembly (Includes Key Nos. 14 &

3

i)

Drawer End Cap

Thumb Screw (4 Required)
Drawer Clamp (2 Required)
Blower Wheel, Counterclockwise

Motor Retaining Ring (2 Required)
Rubber Motor Mount (4 Required)

Motor

Bfower Mounting Rod Nut (2 Required)
Blower Mounting Rod (2 Required)
Blower Scroll Housing

Blower Wheel, Clockwise

Filter Spring (2 Required)
Filter Foam

Filter Panel
Light Lens

Screw #8-18 X 'A (2 Required)'
Plastic Cap (4 Required)

Screw #10-32 X Vi Green (2 Required)
Green Wire Assembly

Complete Blower Assembly (Includes Key

Nos. 5, 34, 35, 36, 37, 40,'41)

Fluorescent Light Tube F20T12' (Not

Included)

Instruction Book

"Standard Hardware. May be purchased locally.

"Not Illustrated.

This manual is related to the following products: