CEI 440 ULTRAK User Manual

Page 2

CHRONOGRAPH MODE:

1. From the ALARM mode, depress C once to go to the CHRONOGRAPH mode. The display

format is as shown in Fig. 7. The chronograph is either in the CUMULATIVE SPLIT or the LAP

mode (depending on previous setting) with their corresponding indicators blinking. Depress A to

START or STOP the CHRONOGRAPH and B for the SPLIT or LAP times. In the CUM SPLIT

mode the display always shows the time from the START to the time at the depression of B

whereas in the LAP mode the display always show the time between the last 2 depressions of B.

When the B button is depressed to show the CUM SPLIT or LAP times, the RUN indicator is

blinking to show that the CHRONOGRAPH is running. Depressing B when the CHRONOGRAPH

is stopped resets it.

2. Depress D to toggle between CUMULATIVE SPLIT and LAP modes.

Fig. 7(a)

LAP

IND.

Fig. 7(b)

CUM

SPLIT

IND.

Fig. 5

ALRAM

HOUR

ALARM

MIN.

ALARM

NO.

Fig. 6

HOURLY

CHIME

IND.

ALARM

IND.

3. When ALARM HOUR is set, press B to display the ALARM TIME with no digits blinking. In this

mode depressing B will enable the hourly chime, the hourly chime indicator will be turned on and

the stopwatch will give 2 short beeps on every turn of the hour. Depressing A will enable the

alarm with the ALARM indicator turned on, as shown in Fig. 6.

4. Depress D to go to the 2nd, 3rd and 4th ALARMS sequentially, Repeat steps 2 and 3 to set the

alarm times.

5. When the set time of any one of these alarms is approached, the alarm will sound, 3 beeps per

sounds for 30 seconds. Depressing any button during sounding will stop the sound.

REMARKS: Switching between modes using the C button will not affect the contents inside each

mode.

Fig. 9

PACER MODE:

1. From the TIMER mode, depress C once to go to the PACER mode. The display is as shown in

Fig. 9. The last few digits can be 60, 70, 80, 100, 120, 160 or 240 (no. of beeps per mintue)

depending on previous setting. Press B to select frequency. Depress A to start or stop the

PACER. When the PACER is in operation the frequency digits are blinking.

2. Depressing C in the PACER mode will return to NORMAL TIME mode.

3. Depress A to START or STOP the timer. When the time approahes zero the alarm will sound, 2

beeps per second, for 30 seconds. Depressing any button when the alarm sounds stops the

sound.

4. When the TIMER is in the COUNT DOWN then COUNT UP mode the timer will count down to

zero then counts up. If it is in the COUNT DOWN then REPEAT mode it will count down to zero,

then counts down again from the originally set time. In both cases the timer will sound for 30

seconds or until a button is depressed.

2. Depress and hold B for 2 seconds to enter the SET TIMER mode with the SECONDS digits

blinking. Depress A to set SECONDS. When SECONDS are set depress B to enter the SET

TIMER MINUTES and SET TIMER HOURS modes respectively and the contents can be set by

using A. After the TIMER HOURS are set depress B to return to the TIMER mode with no digit

blinking.

Fig. 8(a)

COUNT DOWN THEN COUNT UP

Fig. 8(b)

COUNT DOWN THEN REPEAT

TIMER MODE:

1. From the CHRONOGRAPH mode, depress C once to go to the TIMER mode. The display is as

shown in Fig. 8. The timer is either in the COUNT DOWN then COUNT UP mode (as in Fig. 8a)

or in the COUNT DOWN then REPEAT mode (as in Fig. 8b), depending on previous settings.

Press D to switch between these two modes.