Audiovox AX-900 - Manual (Page 20)

128-6996A
20 of 28
20
REMOTE START SELECTABLE FEATURES
Feature Lts Flash 1X Lts Flash 2X Lts Flash 3X Lts Flash 4X Default LED Pattern
1 RF Start Chirp Off On On 1X Pause,etc...
2 Run Time 5 Min. 10 Min. 15 Min. 20 Min. 10 Min 2X Pause,etc...
3 Park Lights On Steady Flash Steady 3X Pause,etc...
4 Input Check Voltage Tach Tach 4X Pause,etc...
5 Voltage Level > 0.5V B4 Start < 0.5V B4 Start > 0.5 5X Pause,etc...
6 Ign. 2 Crank Off On On 6X Pause,etc...
7 Diagnostics Off On Off 7X Pause,etc...
8 Crank Time 0.8Sec 1.0 Sec 1.5 Sec 2.0 Sec 1.0 8X Pause,etc...
9 Gas/Diesel Gas Diesel 10 Diesel 15 Diesel 20 Gas 9X Pause,etc...
10 Trans. O/P While RS On During Start Until Ign Off While RS 10X Pause,etc..
11 Temp Start Off On Off 11X Pause,etc..
NOTE: When selecting Diesel operation, (Feature Nine), over gasoline, the only change is to the ignition circuits.
When Diesel is selected, the ignition circuits will power up 10, 15, or 20 seconds before the start circuit. The
intent of this feature is to allow the glow plug warming required by some diesel engines. If your vehicle is a
instant start diesel, it is not necessary to activate this feature.
NOTE: When selecting Diesel mode, be certain that the intended vehicle has a true tach reference and be certain
to connect the tach input wire.
To Program The Remote Start Selectable Features:
1. Turn the ignition key to the On position.
2. Press and release the valet/program switch three times.
3. Immediately turn the ignition key Off then press transmitter start button for 1 second.
4. Immediately turn the ignition key back On.
5. Press and release the valet/program switch two times. The siren will emit 2 short and 1 long chirp verifying you
are in the feature program mode.
6. Use button 1 on the transmitter to advance to the feature you want to change. EXAMPLE- If you need to change
selectable feature 3, press and release channel 1 button on the transmitter 3 times in succession. The parking
lights will flash and the siren will chirp 3 times confirming that selected feature 3 can be changed.
7. Use the start button on the transmitter to change the selection of the programmable feature. If you are not sure
what the setting for any feature is, press the start button one time; the parking lights will flash once or twice
indicating the features setting.
NOTE: Once you've entered the program mode DO NOT allow more than 15 seconds to pass between steps, or the
programming mode will be terminated.
Programming Tach Rate:
NOTE: All applications require that tach be programmed.
The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via the remote start
without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and
stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is
running and, in certain instances, may try to reengage the starter motor.
The Remote Start Unit will learn the tach rate of most vehicle's single coil, multiple coil packs, or single injector. To
learn tach.
1. Turn the ignition key to the On position.
2. Press and release the valet/program pushbutton switch 3 times.
3. Immediately turn the ignition key Off.
4. Press and hold the valet/program pushbutton switch; then start the vehicle using the key.
5. When the unit senses the tach signal, the parking lights will begin to flash.
6. Release the valet/program pushbutton switch. The parking lights will turn on for three seconds to indicate that the
learned tach signal is stored and the unit is out of the tach learn mode.