Panasonic KX-T206 - Manual (Page 8)

System Programming
Other Programs
Call Blocking Mode Setting
Assigns whether or not to prevent the DTMF
signal from being sent to a CO line. This feature
is useful when a Central Office in your country
accepts both tone and pulse signals or when you
have access to your host PBX with a pulse dial.
Input Format: #20 [A]
• [A]=0; DISABLE (default)/ 1: ENABLE
• Host PBX Access Code Assignment
Assigns a Host PBX access code to make an
outside call, if the system is installed behind the
host PBX. A pause is automatically inserted
after the access code and the toll restriction
feature applies to the number after the code.
Input Format: #21 [A] [code] #
• [A]=l: COl/2: C02
• [code] = 2 digits max. (Default: Not stored)
Hookswitch Flash Time Assignment
Sets the time to send the flash signal to each CO
line.
Input Format: #22 [A] [B]
• [A]=l; COl/2: C02
• [B]=0: 80 ms/ 1: 100 ms / 2: 160 ms/ 3; 300 ms/
4: 600 ms (default) / 5: 900 ms /
6: 1200 ms
CO Pulse Selection
Assigns to send the pulse to CO line during a
conversation with an outside party when the “#01
Dial Type Selection” program is assigned as
“Pulse”.
Input Format: #23 [A]
• [A]=0: DISABLE/ 1: ENABLE (default)
Call Incoming Mode Selection
Assigns whether to use the DISA feature or not.
This program is available when the DISA/FAX
Detect card is installed.
Input Format: #24 [A] [B]
• [A]=l: COl/2: C02
• [B]=0: NORMAL/ 1: DISA (default)
Bell Off Detection
Sets the time between one bell signal detection
and the next signal from a Central Office.
Input Format: #25 [A]
• [A]=l: 6 SEC (default)/ 2: 12 SEC
Intercom Alerting Assignment
Assigns the intercom alerting mode to extension
21 when an intercom call reaches extension 21.
Input Format: #30 [A] [B]
• [A]=l (extension 21)
• [B]=0: TONE (default)/ 1: VOICE
Paralleled Telephone Connection
Assigns whether extension 21 will be connected
in parallel with a single line telephone or not.
Input Format: #31 [A] [B]
• [A]=l (extension 21)
• [B]=0: DISABLE (default)/ 1: ENABLE
Executive Busy Override
Determines whether extension 21 performs the
Executive Busy Override feature.
Input Format: #32 [A] [B]
• [A]=l (extension 21)
• [B]=0: DISABLE (default)/1: ENABLE
Tone Waiting Time After OGM
Sets the time between sending an outgoing
message and sending the ringback tone.
Input Format: #40 [A]
• [A]=0: 0 SEC/ 1: 5 SEC (default)/ 2: 10 SEC/
3: 15 SEC
4
Hold Recall Time
Assigns the length of the hold recall timer and
transfer recall timer. The hold recall timer is
used to alert an extension that a call has been
held for an extended period of time. The
transfer recall timer is used to alert an extension
that a transferred call has not been answered for
an extended period of time.
Input Format: #50 [A]
• [A]=0: 30 SEC (default)/ 1: 1 MIN / 2: 2 MIN/
3: 3 MIN/ 4: 4 MIN/ 5: DISABLE
• Hold Mode Selection for SET
Assigns the method to put a call on hold with
SLTs.
Input Format: #51 [A]
• [A]=l: MODE 1 (hooking) (default)
2: MODE 2 (hooking and dial 6)
4
CO Line Access Number Selection
Selects the automatic line access number.
Input Pormat #52 [A]
•[A]=l:9/ 2:0 (default)
Conference Tone
Assigns whether or not to delete the conference
tone. You hear the tone when the conference or
the executive busy override feature begins and
finishes.
Input Format: #53 [A]
• [A]=0: DISABLE/ 1: ENABLE (default)
26