BendixKing AV8OR Ace - Quick Reference Guide - Manual (Page 2)

FLIGHT PLANNING
Create a Flight Plan (Data View)
1. On the aviation Main Menu, tap the Flight Plan
soft key and then highlight the NEW FLIGHT PLAN
line and tap the NEW FPLAN soft key.
2. Tap on the INSERT soft key to open the virtual
keyboard page.
3. Enter an IDENT, Name, Location or Airway.
4. Tap on the Enter soft key .
5. Tap on the OK soft key to enter the selected
waypoint into the flight plan.
6. Repeat steps 2 to 5 for additional waypoints.
7. Tap on the SAVE & EXIT soft key to create the
flight plan.
8. Select the flight plan just entered.
9. Tap on the FLY FPLAN soft key to activate the
flight plan.
Create a Flight Plan (Map View)
1. On the aviation Main Menu, tap the Flight Plan
soft key and then highlight the NEW FLIGHT PLAN
line and tap the NEW FPLAN soft key.
2. Tap on the MAP VIEW soft key.
3. Pan through map with finger or stylus to locate and
tap on the first waypoint.
4. Tap on the INSERT WPT soft key.
5. Repeat steps 3 and 4 for additional waypoints.
6. When complete, tap on the CLEAR PTR soft key.
7. Tap on the SAVE & EXIT soft key.
8. Select the flight plan just entered.
9. Tap on the FLY FPLAN soft key to activate the
flight plan.
XM WEATHER (Optional)
1. On the Aviation Main Menu, tap on the WEATHER
soft key to show XM weather. You must have the
XM receiver installed properly and an active
subscription before weather can be shown on the
Weather page.
2. Tap on the CHOOSE PRODUCT soft key to select
the type of weather product that shows on the
Weather page.
Note: Until current XM data has been received from the
XM receiver, a caution message will be displayed on the
weather page. Assuming good signal strength a
complete set of XM weather data will be received every
12 minutes. The initial data displayed is dependent upon
where in that 12 minute cycle the data was received.
CHARTS AND
PROCEDURES
To display the Charts page, tap an Airport icon on the
MAP page . Then tap the MORE INFO soft key.
Shortcut: If the airport is displayed in a DEST WPT or
WPT Data Window, tap on the Data Window twice to
display the Airport MORE INFO screen.
Tap the CHART soft key to show the Charts/Procedure
Page for the selected airport.
Tap the Airport tab to show an airport diagram.
Tap the SID tab to show SIDs for the selected airport.
Tap the STAR tab to show STARs for the selected
airport.
Tap the Apprch tab to show Instrument approaches for
the selected airport.
Tap the selected airport identifier (KMCI in above figure)
and then tap the EDIT soft key to change the
Charts/Procedure Page to a different airport. Highlight a
procedure or airport diagram and tap the LOAD VIEW
soft key to add the selection to the VIEW hard key.
AUTOMOTIVE
Go Drive Main Menu
•
Tap on the Find Address soft key to find your
destination and start navigating.
• Tap on the Find POI soft key to find Points Of
Interest.
•
Tap on the History soft key to show a listing of the
points previously visited.
•
Tap on the Favorites soft key to view a listing of
the user’s favorite places.
•
Tap on the Map soft key to show the map page.
•
Tap on the Settings soft key to change the settings
for Go Drive or to change between Simple and
Advanced Navigation modes.
•
Tap on the Exit soft key to close the automotive
mode and return to the Main Menu.
CONTROLS AND INDICATIONS
1 2 3
7
4
6
9
8
5
1 Turn Preview field
2 Main Map
3 Map Scale (Only in 2D mode)
4 2D / 3D soft key
5 Detour soft key
6 Cursor soft key
7 Menu soft key
8 Status Field (Soft key to Quick Menu)
9 Trip Data Field
AUTOMOTIVE MAP TIPS
Selection of a Destination
1. Pan to and then tap the point on the screen where
you would like to go.
2. Tap on the Cursor soft key (6) to activate the
cursor.
3. Tap on the Navigate To soft key to navigate from
your current position to the selected point.
To Find a Point of Interest (POI)
(From an active route)
1. Tap on the Menu soft key (7).
2. Tap on the Find POI soft key.
3. Tap on one of the categories.
4. Tap on the Search soft key to display the virtual
keyboard page.
5. Enter the POI name and tap on the Done soft key.
6. Select the POI from the list.
7. Tap on the Select soft key to view the POI.
8. Tap on the Navigate To soft key to start navigation.
To Find an Address
1. Press the DIRECT TO hard key (item 6 on page 1)
to go to the Find Address page.
To Zoom In/Out on the Map
1. Tap on the Map Scale (3) or double tap anywhere
on the map (2) to show the Magnifying Glass.
2. Tap on the Magnifying Glass soft key
3. Use the Plus and Minus soft keys on the left side
of the page to zoom in and out or press the “+” or “–
“ side of the ZOOM IN/ZOOM OUT hard key (item 5
on page 1).
To Tilt the Map
1. If in 2D mode, tap the 3D soft key (4).
2. Tap on the Map Scale (3) or double tap anywhere
on the map (2) to show the Magnifying Glass.
3. Tap on the Magnifying Glass soft key.
4. Tap the Up Arrow to tilt up, the Down arrow to tilt
down, the Left arrow to pan left and the Right
arrow to pan right.
AUTOMOTIVE MAP TIPS
Tap the Magnifying Glass soft key to disable zooming
or tilting.
Manual change between Day/Night Mode
1. Tap on the Status field (8).
2. Tap on the Half Moon soft key.
To View Speedometer/Trip Computer
1. Tap on the Trip Data field (9) to see an enhanced
speedometer and data.
2. Tap on the Trip Computer soft key to see current
trip data.
Advanced Mode Features
•
From the Main Menu, tap on the Settings soft key
to change to Advanced Mode.
•
Trip Data fields are configurable.
•
Trip Computer is available thru the Status Field.
•
Multi-point routes can be created.
•
Traffic Message Channel (TMC) is available
•
See User manual for complete details.
Frequency Asked Questions (FAQs)
For FAQ’s go to
0H
http://www.bendixking.com/av8or
Proprietary Notice
This document and the information disclosed herein are
proprietary data of Honeywell, Inc. Neither this document nor the
information contained herein shall be reproduced without the
written authorization of Honeywell Inc. Notice – Freedom of
Information Act (5 USC 552)
This document contains Technical Data and is being exported
under General License GTDU. No validated export license is
required. E.A.R. Section 779.4 (b): ECCN 7E994; Schedule B
Number 4901.99.0050; License Exception TSU
Customer support, in the US & Canada, please call 1-877-712-
2386, all other countries 1-913-712-2613, or send an email to
[email protected] or you may go the web site
at
1H
http://www.bendixking.com/av8or .
Document is not under Distribution control.
Pub D200904000016 July 2009.
© 2009 Honeywell International Inc. All rights reserved
23500 West 105
th
Street, Olathe, KS 66061
Bendix King by Honeywell Page 6
AV8OR ACE Quick Reference Guide Bendix King by Honeywell Page 8
AV8OR ACE Quick Reference Guide Bendix King by Honeywell Page 10
AV8OR ACE Quick Reference Guide Bendix King by Honeywell Page 9
AV8OR ACE Quick Reference Guide Bendix King by Honeywell Page 7
AV8OR ACE Quick Reference Guide