Channel Vision A4603 - Manual (Page 3)

2
3
Accessories
(Sold Separately)
IR-3001 & IR-3002 ... Single and dual head IR flashers.
Use one head per source to control from the remote
room. (IR-3002 shown).
A0501 or A0502 ... Remote control. Contains IR codes
for controlling the A4603 as well as many other Channel
Vision audio products. (A0501 shown).
A0127 ... IR repeating keypad. The A0127 already
contains the IR codes necessary to operate the A4603,
but you may also use a standard IR receiver or a 3rd
party keypad. When using a simple IR receiver, you will
need to use the A0501remote control which contains
the IR codes to control the A4603. These codes can be
downloaded from www.channelvision.com, or learned
from an A0501 remote control.
Pwr Mute
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
T M
I
C
H
A
N
N
E
L V
S I O
N S O U R C E
Z O N E
PO W ER
M U T E
V O L
1 2 3 4
O
E L
M
D 5 0 1
A 0
P O W
E
R
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions for future reference
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this device near water.
6. Clean only with a dry cloth.
7 Do not block any ventilation openings. Install in accordance with
these instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that produce
heat. When installing multiple amplifiers in the same rack, provide
space for air circulation above and below each unit.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug, has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. the
wide blade or the third prong are provided fro your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories specified by Channel Vision.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
15.
Warning: To reduce the risk of electric shock, do not remove the cover
(or back), no user serviceable parts inside, refer servicing to qualified
service personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
Aria By Channel Vision 4x6 matrix Controller
A4603 Aria By Channel Vision
4x6 matrix Controller
A4603R
3.50”
14.5”
16.75”
19.0”
A4603R A4603
Features:
! Pre-amp outputs are a prefect match for the A1260 multichannel amplifier
! Distributes 4 A/V sources to 6 different zones
! IR and Serial Control options
! Cost effective and easy to install
The A4603/A4603R is a 4 input 6 zone matrix A/V controller with pre-amp
outputs for each of the 6 zones making it easy to integrate with a high power
multichannel amplifier such as Channel Vision’s A1260. Any of the 4 source
inputs can be selected and routed to any of the 6 outputs (or zones)
independent of the other zones.
Dimensions do not include the rubber feet on the bottom of the unit or
connectors which protrude from the rear of the unit. Rubber feet will add 0.5” to
the height and connectors (without wires attached) will add 0.5” to the depth.
Note: at frequencies between 150kHz to 1GHz, any deterioration of the
sound and picture is so minor that the system could still be used and
will function normally.