Airless paint systems, Tip selection chart, Operation – Campbell Hausfeld AL2710 User Manual

Page 7: Orifice size, Warning, Al2710

Airless Paint Systems

Operating Instructions and Parts Manual

www.chpower.com

Quadraflow

Tip

for painting

(12" from surface)

Fan Width (in.)

(mm)

.009

.011

.013

.015

.017

.019

.021

.023

.025

.027

.035

4-6

102-152

6-8

152-203

AL3116 AL3117

AL3119

AL3122 AL3125

8-10

203-254

AL2211

AL2213

AL3126

AL3131

10-12

254-305

AL3118

AL3120

AL2215 AL2217

AL3130

AL3132 AL3135 AL3137

AL3139

12-14

305-356

AL3121

AL3124 AL3127

AL2219

AL2221 AL3136 AL3138

AL3140

14-16

356-406

16-18

406-457

AL3134

Gun Filter

2 types (part #)

l---------AL086101AJ------l

l--------------AL086100AJ---------------l

Lacquer, Varnish

Stain, Sealer

Enamel

Exterior Stain

Vinyl, Acrylic, Latex

Vinyl, Oil Base Alkyd

Latex, Acrylic

Block Filler

Elastomer

Ceiling

Hi Build, Mil White

Structural Steel

Heavy Coatings

Water Flow Rate

(gpm)

.12

.18

.24

.31

.38

.47

.57

.67

.77

1.03

1.31

(water @ 2000psi,
138 bar)

(lpm)

.49

.69

.91

1.17

1.47

1.79

2.15

2.54

2.96

3.90

4.98

Paint Flow Rate

(gpm)

.10

.15

.21

.27

.33

.40

.49

.58

.66

.88

1.12

(latex paint @ 2000psi, 138

bar/1.36 spec. gr.)

(lpm)

.38

.57

.79

1.02

1.25

1.51

1.85

2.20

2.50

3.33

4.24

(gpm)

.25

.33

.40

.50

.60

.75

.88

1.00

1.25

1.50

(lpm)

1.00

1.25

1.50

1.90

2.30

2.80

3.30

3.80

4.70

5.70

Orifice Size

(inches)

Tip Selection Chart

Consult your paint manufacturer for application recommendation

*pump will support tip worn to next larger size.

.029
.031

Pump Minimum
Output*

Wood Interior

Wood Exterior

Masonry

REMOVE FILTER

Operation

(Cont.)

hand, body fingers or hand in front of
spray tip when cleaning or checking for
a cleared tip. Always point the gun
toward the ground or into an empty
container when checking to see if the
tip is cleared or when using a self-
cleaning tip. Always remove tip before
cleaning.

NOTE: When pausing during a paint
job, keep tip clean by locking the gun
and submerging the tip in a small
bucket of paint thinner. This will help

reduce buildup and drying of paint in
tip, tip guard, and gun.

7. When shutting off the sprayer,
follow this procedure.

a. Whenever you stop spraying,
even for a short break, follow the
Pressure Relief Procedure on page 3.

b. Clean the tip and gun as
recommended by your separate
gun instruction manual.

c. Flush the sprayer at the end of
each work day if the material you

are spraying is waterbased, or if it
could harden in the sprayer
overnight. See "Flushing" page 4.
Use a compatible solvent to flush,
then fill the pump and hoses with
an oil based sovent such as mineral
spirits.

d. For long term shutdown or
storage, refer to page 4.

Be sure to relieve
pressure in the

pump after filling with mineral spirits.

WARNING

Table 2 - Tip Selection Chart

AL2710