Oldcastle BuildingEnvelope MS-360 User Manual
Page 2
![background image](/manuals/638822/2/background.png)
M S 3 6 0 I N S T A L L A T I O N I N S T R U C T I O N S
GENERAL INFORMATION:
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Assembly Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4 – 5
Glass Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6 – 7
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
CONTENTS
2
M S - 3 6 0 I N S T A L L A T I O N M A N U A L
PRODUCT USE
The MS-360 mall sliding storefront system
by Oldcastle BuildingEnvelope™ is
intended for installation
by glazing professionals with appropriate experience. Subcontractors without experience should employ a
qualified person to provide field instruction and project management.
Oldcastle BuildingEnvelope™ does not control the application or selection of its product configurations, sealant
or glazing material and assumes no responsibility thereof. It is the responsibility of the owner, architect and
installer to make these selections in strict compliance with applicable laws and building codes.
Consult sealant manufacturer for review and recommendation of sealant application. Follow sealant
manufacturer’s recommendations
and literature for proper installation.
PROTECTION AND STORAGE
Handle all material carefully. Do not drop from the truck. Stack with adequate separation so the material will
not rub together. Store material off the ground, protecting against the elements and other construction hazards
by using a well ventilated covering. Remove material from package if wet or located in a damp area. For further
guidelines consult AAMA publication CW-10, “Care and Handling of Architectural Aluminum From Shop to Site.”
CHECK MATERIAL
Check all material upon arrival at job sit for quality and to determine any shipping damage.Any visible damage
must me noted on the freight bill at the time of receipt. If a claim is required, then the receiving party must process
Using the contract documents, completely check the surrounding conditions that will receive your materials.
a claim with the freight company.
Notify the general contractor by letter of any discrepancies before proceeding with the work. Failure to do so
constitutes acceptance of work by other trades.
Check shop drawings, installation instructions, architectural drawings and shipping lists to become familiar with
the project. The shop drawings take precedence and include specific details for the project. The installation
instructions are of a general nature and cover the most common conditions. Due to varying job conditions all
sealant used must be approved by the sealant manufacturer to insure it will perform per the conditions shown on
the instructions and shop drawings. The sealant must be compatible with all surfaces in which adhesion is
required, including other sealant surfaces. Use primers where directed by sealant manufacturer. Properly store
sealant at the recommended temperatures and check sealant for remainder of shelf life before using.
FIELD CONDITIONS
2. All material to be installed must be plumb, level and true. Aluminum to be placed in direct contact with masonry
1. Not recommended for exterior use where door must be water tight.
or incompatible material should be isolated with a heavy coat of zinc chromate, bituminous paint or non-metallic
material.
3. Coordinate protection of install materials with general contractors and other trades.
CLEANING MATERIALS
Cement, plaster terrazzo, alkaline and acid based materials used to clean masonry are very harmful to finishes.
Any residue should be removed with water and mild soap immediately or permanent staining will occur. A spot
test is recommended before any cleaning agent is used.
MAINTENANCE
Keep tracts free of debris, including areas where panels stack. Wax tracks periodically using wax stick. Actual waxing
schedule depends on door use factors, including traffic, season and climate, but once a week in high traffic areas
should keep panels operating smoothly.