beautypg.com

Power source – Curtis RCD224UK User Manual

Page 7

background image

CD PROGRAMMED PLAY 

This function allows the tracks to be played in a programmed sequence. 
1. 

Under  CD  stop  or  playing  condition,  press  the  PROG.  BUTTON  (#2).    The  CD  TRACK  DISPLAY  (#16)  will 

display “01” and the PROG on the display will flash. 

2. 

Press the CD F.FWD  BUTTON (#7) or CD REW BUTTON (#6) to select the song to be programmed. 

3. 

Press the PROG. BUTTON(#2) again to store selection.  The CD TRACK DISPLAY (#16) will advance to “02”. 

4. 

Press the CD F. FWD BUTTON(#7) or CD REW BUTTON(#6) to select the next song to be programmed and 

press the PROG. BUTTON(#2) to store selection. 

5. 

The max. programmable tracks reaches as 20 tracks merely for memory save. 

6. 

Press CD STOP BUTTON (#5) to end programming and return to normal play mode. 

7. 

To check the programmed tracks, press PROG. BUTTON(#2) continuous to show all the programmed songs. 
The CD TRACK DISPLAY(#16)  will  display  the  program number first and  then followed  by  the  flashing  track 

number. 

8. 

Press CD PLAY/PAUSE BUTTON (#8) to begin programmed play.  The first track in program will appear in the 

CD TRACK DISPLAY(#16) and the” PROG” will light steadily. 

9. 

To cancel programmed play, press the CD STOP BUTTON (#5). 

10.  As long as the unit remains on and the CD DOOR(#21) is not opened, you can resume programmed play any 

time by pressing the PROG. BUTTON(#2) and then CD PLAY/PAUSE BUTTON(#8) in stop condition. 

RADIO RECEPTION 

1. 

Set the FUNCTION SELECTOR(#23) to the "RADIO" position. 

2. 

Set the BAND SELECTOR(#24) to either "AM", or “FM” for the desired radio band.  To receive a weak (noisy) 
FM  station,  set  the  BAND SELECTOR(#24)  to  the  “FM” position.   The  reception may be  improved,  but  the 
sound will be monaural (MONO). 

3. 

While  you  switch  the  BAND  SELECTOR(#24)  to  “FM  St”,  once  you  get  the  right  FM  station,  then  the  FM 
STEREO INDICATOR(#20) will be  getting GREEN 

4. 

Adjust the TUNING KNOB(#10) to obtain the desired radio station. 

5. 

Adjust the VOLUME CONTROL (#22) to obtain the desired sound level. 

6. 

When you wish to turn off the Radio, set the POWER ON/OFF BUTTON (#11) to the "OFF" position or switch 
the FUNCTION SELECTOR(#23) to CD / AUX­IN position. 

TIPS FOR GOOD RADIO RECEPTION 

1. 

To  insure  maximum  FM  tuner  sensitivity,  the  TELESCOPIC  ANTENNA(#9)  should  be  fully  extended  and 
rotated  to  obtain  the  best  possible  reception.  The  FM  STEREO  INDICATOR(#20)  will  light  steadily  when  a 
stereo program is being received. 

2. 

When  tuning  in  AM  reception,  be  sure  to  place  the  unit  in  a  vertical  position.  To  insure  the  maximum  AM 
sensitivity, try repositioning the unit until the best reception is obtained. 

AUX IN FUNCTION 

1.  Set the FUNCTION SELECTOR(#23) to AUX IN position 
2.  Plug  the external signal jack into the AUX­IN jack (#12) , then the unit will be used as speaker 
3. 

Adjust the volume by the VOLUME CONTROL(#22) 

4.  Stop this function ,power off the unit or switch the FUNCTION SELECTOR(#23) to other position 
Remark: While using this function , other functional key are invalid except the VOLUME CONTROL( #22) 

USING HEADPHONES (NOT INCLUDED) 

Inserting  the plug of  your headphones  into  the  HEADPHONE JACK  (#13) will enable  you  to  listen  to  the CD  and 
Radio in private. When using headphones, the SPEAKER (#17) will be disconnected. 
READ THIS IMPORTANT INFORMATION BEFORE USING YOUR HEADPHONES
 
1. 

Avoid extended play at very high volume as it may impair your hearing. 

2. 

If you experience ringing in your ears, reduce the volume or shut off your unit. 

3. 

Do not use while driving a motorized vehicle.  This is dangerous and also illegal in some areas. 

4. 

Keep the volume at a reasonable level even if your headset is an open­air type designed to allow you to hear 
outside sounds.  Please note excessively high volume may still block outside sounds.