Attwood PinPoint GPS - Manual (Page 2)

MANUAL
MODE OPERA
TION
After it is power
ed up, the tr
olling motor will operate in
Manual mode by default or if the GPS signal is lost while operating in a GPS mode. T
o
change fr
om any function to
the Manual mode, pr
ess the Manual mode button ( ).
SPEED
CONTROL
•
T
o
start the pr
opeller
, pr
ess the
Pr
opeller
( )
•
T
o
stop the pr
opeller
, pr
ess the
Pr
opeller
( ) button
•
T
o
incr
ease motor speed by one level, pr
ess the
Incr
ease Speed
( ) button
•
T
o
decr
ease speed by one level, pr
ess the
Decr
ease Speed
( ) button
Holding the Increase Speed or Decrease Speed button will cause the speed level to increase to the maximum speed level or decrease to the minimum speed level.
STEERING
•
T
o
tur
n left, pr
ess the
Steer Left
( ) button
•
T
o
tur
n right, pr
ess the
Steer Right
( ) button
The available steering range allows the trolling motor to turn beyond 180° for operation in reverse
GPS
MODE OPERA
TION
Status LED is solid when the motor has GPS fi
x.
Status LED blinks slowly when a GPS mode is active.
SETTING
THE
ANCHOR
POSITION
• Pr
ess
the
Anchor
( ) button to lock curr
ent
GPS
position
ADJUSTING
THE
ANCHOR
POSITION (
JOG
)
While in
Anchor
, the Anchor position can
be adjusted in
fi
ve foot incr
ements (
Jog
), r
elative to boat orientation, in the
dir
ection selected:
• Pr
ess
the
Left arr
ow
( ),
Right arr
ow
( ),
Forwar
d
( ) or
Backwar
d
( )
STORING
AN
ANCHOR
POSITION
•
Pr
ess and hold any of the number
ed
Memory
(
1-8
)
buttons for two seconds
A stored Anchor position can be overwritten with a new Anchor position by repeating the same procedure.
RECALLING
A STORED
ANCHOR
POSITION
•
Pr
ess and r
elease the desir
ed
Memory
(
1-8
) button
If the desired stored Anchor Position is over a mile away from your current location, the trolling motor will emit an error tone.
EXITING
ANCHOR
POSITION
• Pr
ess
the
Anchor
( ) button or pr
ess the
Manual Mode
( ) button
SETTING
THE
HEADING LOCK
T
o
lock in the tr
olling motor’
s heading and navigate in a
straight line: •
Steer the tr
olling motor in the desir
ed dir
ection
• Pr
ess
the
Heading Lock
( ) button
ADJUSTING
HEADING LOCK
The Heading can be adjusted using the Steer Left and Steer Right buttons. The speed can be adjusted by using the Increase and Decrease Speed buttons.
EXITING
HEADING LOCK
• Pr
ess
the
Heading Lock
( ) button or the
Manual Mode
( ) button
RECORDING
AND
STORING
A
ROUTE
• Pr
ess
the
Route Recor
d
( ) button and begin
navigating along your desir
ed Route
Y
ou can use Heading Lock and Manual mode at any time while
recording a Route. Status LED will blink and unit will beep as waypoints are recorded.
•
Pr
ess and hold any of the number
ed
Memory
(
1-8
) buttons to stop r
ecor
ding and to stor
e the Route
The trolling motor will emit a tune to confi
rm that the Route is stored.
To
overwrite a stored route, use the same procedure as Storing a
new Route.
RECALLING
A STORED
ROUTE
• Pr
ess
the
Route Playback
( ) button
•
Pr
ess and r
elease the desir
ed number
ed
Memory
(
1-8
)
button The trolling motor will return you to the nearest point on the recalled Route then navigate the longest leg of the route.
ROUTE
TRA
VEL AND COMPLETION
While travelling along a stored route, the direction of travel can be reversed by recalling the stored route again. Upon reaching the end of a stored route, the system will enter Anchor mode
SETTING
CRUISE CONTROL
• Pr
ess
the
Cruise Contr
ol
( ) button to set the
Cruise Contr
ol at 1.0 mph
Cruise Control can be activated while in Heading Lock or Route Playback.
ADJUSTING
CRUISE CONTROL
SPEED
•
Cruise Contr
ol
( ) speed can be incr
eased
or decr
eased in 0.1 mph incr
ements by using the
Incr
ease Speed
( ) button or
Decr
ease
Speed
( ) button
EXITING
CRUISE CONTROL
• Pr
ess
the
Cruise Contr
ol
( ) button to tur
n of
f
Cruise
Contr
ol
© 2014 MotorGuide / Lowell, MI 49331 / motor
guide.com
69527 Rev
. A