Attwood 12-Volt 1-Mile Navigation Lights User Manual
Volt 1-mile navigation lights

12-Volt 1-Mile Navigation Lights
66314 Series
3
®
Attwood marine hardware, navigational lighting, bilge pumps, and
other marine accessories are specified more than any other brand by
America’s best-known boat manufacturers as original equipment.
Look to Attwood for quality replacement parts and marine accessories.
SAVE THESE INSTRUCTIONS
Form Number 69338 Rev. B
03-10
FEATURES
Your new Attwood 12-Volt, 1-Mile Vertical Mount Navigation Side-
lights are for boats up to 39.6 ft. (12 meters). Housings are of
highly-polished, corrosion resistant stainless steel. Lens and gasket
completely encapsulates the bulb and socket assembly for a splash
resistant seal. These lights meet the ABYC A-16 standard.
REQUIRED FOR INSTALLATION
• Cordless drill with suitable bits.
• Phillips head screwdriver.
• Marine sealant.
WARNING:
To prevent personal injury, always disconnect the power source when
installing or servicing this product. Always remove the boat from the
water before using 120V AC power tools.
LOCATION
Lights must be mounted to an unobstructed smooth vertical surface
on the exterior cabin bulkhead or superstructure parallel to the water
line. Red to port (left) and Green to starboard (right). (Figure 1)
Figure 1
Figure 3
FINAL WIRING
CAUTION:
Power source must be positive 12V DC only. All positive (+12V DC)
wires must be fused with a 2-amp fuse to protect the circuit. Failure to
make proper connections and fusing will void product warranty.
1. Neatly thread wires to dash avoiding any areas where abrasion or
snagging may occur.
2. Use waterproof crimp on butt joint connectors to attach wires to a
switch on the dash that allows for two-position operation — one for
running lights and one for anchor lights. Test lights for proper
operation. (Figure 3)
MAINTENANCE
For cleaning or to replace bulb, remove three screws in housing.
Remove housing, lens and gasket. Push bulb in and turn counter-
clockwise to remove. Replace with 7.5 watt Attwood #8020-15.
Reinstall assembly and tighten screws. (Figure 2)
1. Using base as a template, mark the center location of the bulb
socket opening in the base and all mounting screw holes.
2. Drill 3/4" (19mm) diameter hole for bulb socket and 1/8" (3mm)
pilot holes for all mounting screws.
3. Bring 12V DC (+) and (-) wires up through hole.
4. Connect wires using waterproof crimp on butt joint connectors.
5. Activate light to verify proper operation.
6. Snap bulb socket into opening in base.
7. Apply marine sealant to the bottom of base around bulb socket to
prevent water from entering hull or cabin.
8. Push wires and bulb socket into 3/4" (19mm) hole and align
screw holes.
9. Align gasket, lens and housing with base and fasten with stainless
screws. Do not over tighten. (Figure 2)
112.5
°
Green
Starboard
112.5
°
Red
Port
INSTALLATION
Figure 2
•
12V DC
Green Starboard
Red Port
Neg. (-)
Pos. (+)
2-Amp Fuse
3-Way Switch
•
•
This product carries the standard Attwood one year warranty.
See Product Catalog for details.
Gasket
•
Base
•
Bulb
•
•
•
Lens
•
Housing
•
Mounting Screw
•
1/8" (3mm) Pilot Holes
3/4" (19mm)
Dia. Hole
•
Butt Joint Connectors
© 2003 Attwood Corporation
1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com