beautypg.com

5gb instruction manual – Scarlett SC-446 User Manual

Page 5

background image

www.scarlett-europe.com

SC-446

5

GB

INSTRUCTION MANUAL

IMPORTANT SAFEGUARDS
· Before the first connecting of the appliance check that voltage indicated on the rating label corresponds to the mains voltage in your home.

· For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described in this instruction manual.
· Do not use outdoors.
· Always unplug the appliance from the power supply before cleaning and when not in use.

· To prevent risk of electric shock and fire, do not immerse the appliance in water or in any other liquids.
· Close supervision is necessary when it is used near children or invalids.

· Do not leave the appliance switched on when not in use.
· Do not use other attachments than those supplied.

· Do not operate after malfunction or cord damage.
· Do not attempt to repair, adjust or replace parts in the appliance. Check and repair the malfunctioning appliance in the nearest service center only.
· Keep the cord away from sharp edges and hot surfaces.

· Do not pull, twist, or wrap the power cord around appliance.
· Never attempt to take food or liquid out from the container when the blade is moving. Always wait until the motor stops completely.

· Do not overload the appliance with food.
· The appliance operates fast and effective. Do not operate continuously for more than 1 min.

· Never place hot ingredients into processor (> 70 ºC)

.

FOOD PROCESSOR ASSEMBLING

· Before the first using, wash all removable parts in warm soapy water, rinse thoroughly and dry. Wipe the housing with a damp cloth.
· Never immerse motor body in any liquid or wash under running water.
· Place the motor unit on a level surface.
ATTENTION: Never operate processor bowl and blender at the same time.

· Place the bowl on the motor unit.
· Place blender gear safety lid on the seat, rotating until fixed securely.
ATTACHMENTS

· Use ONLY ONE attachment for food processing.
CUTTING KNIFE\PLASTIC BLADE
· Fit shaft adaptor into the blade (or whip maker) until it fixed securely.

· Fit shaft adaptor on the bowl drive spindle.
· Load products to be processed in the bowl.
·

Place lid on the bowl and rotate it to lock.

· Turn bowl clockwise to the proper position
· Start processing at high speed (position ).
DISKS - GRATING / SLICING / SHREDDING
· Set the slicer, grater or shredder knife in the supporting disc and place it onto shaft adaptor.

· Fit the disk with the spindle onto the blender shaft.
NOTE: you must complete assembling fully; otherwise you cannot switch on device.
FOOD PROCESSOR USING

· Please make sure accessories are at its places before switching on.
· Plug-in device.
PULSE MODE
It is provided two ways of turning on a pulse mode

-

Turn the Speeds control switch to

position.

-

Press and retain the Pulse button - food processor will operate till this button is pressed.

· Before processing cut a food so it would pass through a feeder easily.

· Turn control switch to speed "1" (low speed) or "2" (high speed), so food processor will work continuously until you turn back to "0" (switch off).
· Gradually feed products to be processed through the feed tube only while processor is operating.

CAUTION: Use the pusher only to feed products, push it evenly and gently. The heavier pressure, the coarser chopping.
CAUTION: Do not operate continuously longer than 1 minutes with less than 1 minute intermission.

· Do not overload the appliance by putting in too much food.
· Do not remove any parts during the operating.
BLENDER
· Leave the processor bowl at the place locked into the slot. Remove shaft adaptor and attachments; do not place food in the processor bowl.

· Open blender gear safety cap.
· Place the blender jug onto the blender gear. Make sure it properly fitted.

· Put ingredients into blender jar, and close it with the lid.
· Plug-in, turn the switch/press buttons to recommended speed:

"1"(low speed) for liquid ingredients mainly.

"2" (high speed) for heavier processing, i.e. liquid and solid ingredients mixtures.

The appliance will operate until it will be switched off.

- PULSE mode.

· Blender could process fruit juices, ice-cocktail, etc.
CITRUS PRESS SET
· Place the strainer on the bowl then turn the handle until it locks into the bowl lid-locking slot.

· Place the cone into the hole in the strainer.
· Press on a half of a fruit to the cone.

· Turn Speeds control switch to (slow speed) to start the appliance. For greater control use the Pulse mode.
CAUTIONS:
· Avoid operating the empty blender;
· Never place hot ingredients into blender jar (> 70 ºC);
· Ingredients must be cut into small pieces before processing in blender jar;

· Never fill blender jar with a liquid over maximum level marked;
· When processing is finished, switch off, and then unplug the appliance and wait the motor will stop before removing a food and attachments.
CLEANING AND CARE
· Switch off and unplug the appliance.

· Wash the accessories immediately and avoid soaking them in water for long periods; wash in warm sudsy water after each use. Dry all accessories

with a clean soft cloth.

· Wipe housing with a damp cloth.
· Do not use scouring pads, abrasive and harsh detergents.
CLEANING THE BLENDER JUG
· Place empty blender jug onto the motor unit and cover with the lid.