Cooper Instruments & Systems DFI INFINITY Digital Force Indicator/Controller - Manual (Page 2)

5 6 7 8
To Configure Scaling Factor:
1. Press ᮣ /MIN to display and to select
the digit (or decimal point) you want
to change.
2. Press ᮡ /MAX to increase the value
of the selected digit.
3. Repeat steps 1 and 2 until each digit is the desired value
(your calculated scaling factor).
4. Press MENU.
The meter displays:
To Configure Meter Inputs:
1. Press MENU until
the meter displays:
2. Press ᮣ /MIN to display:
3. Press ᮡ /MAX, if necessary to change the configuration
value.
4. Repeat steps 2 and 3 for INP.2 through INP.7
5. Press MENU.
The meter displays:
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
in.sc.of
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
stored
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
inp.1=0
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
in cnf
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
rdg of
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
stored
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
0.00000
To Configure Type of Input:
1. Press MENU until the
meter displays:
2. Press ᮣ /MIN to display a flashing input type.
3. Press MENU.
The meter displays:
4. Press MENU and bridge stops flashing.
5. Press MENU.
The meter displays:
To Configure Meter Display Readings:
1. Press ᮣ /MIN to display:
2. Press ᮡ /MAX, if necessary to change the configuration
value to 0 or 1 .
3. Repeat steps 1 and 2 for RDG.2 through RDG.7
4. Press MENU.
The meter displays:
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
rdg SC
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
stored
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
rdg.1=0
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
rdg.cnf
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
stored
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
bridge
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
stored
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
input1
To Set Decimal Point Position:
1. Press MENU until
the meter displays:
2. Press ᮣ /MIN to display:
Press ᮡ /MAX to move
the decimal point to the
desired location.
3. Press MENU.
The meter displays:
4. Press RESET twice. The meter flashes
and displays an output reading.
The meter is now in RUN mode.
Configure Reading Offset
Now that you are in the run mode with a transducer connected
to the meter, do the following:
1. Simulate a load on the transducer (leave the pressure
port open).
2. Note the display reading. LetÕs assume
the display shows 43.5.
3. To make the display show zeroes, press
MENU until the meter displays:
4. Press ᮣ /MIN to display the previous reading offset value.
5. Using ᮣ /MIN to scroll through the digits
and ᮡ /MAX to change the value, enter
the value -0043.5.
6. Press MENU.
The meter displays:
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
reset2
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
cntby
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
stored
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
FFFF.FF
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
DeC pt
7. Press RESET twice.
The meter flashes and
then displays a value.
Your meter is now in RUN mode and operational.
If You Have Bipolar Input ±50mV
The typical setting for your meter is unipolar. If, however, you
have bipolar input ±50mV, you must install jumper S1B.
Remove the outer panel mounting sleeve to expose the
jumper.
S1 Jumper Location on Signal Input Board
In addition, you must set configuration menu value INP.3=1
(under IN CNF menu). Refer to the Configuration sections of
this Quick Start manual.
A B A D G H V L P S T U
B
C
E
F J
K
N
M R
Q
S2
J3
J9
S1
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
reset2
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
stored
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
in cnf
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
rdg of
ᮡ ᮣ SETPTS /MIN MENU RESET /MAX
-0043.5
MQS1291/N/0401
12458ML-01 Rev. D